Technical Data - Bosch GHO 6500 Professional Notice Originale

10 | English
A)
(28) Rebate depth guide
(29) Parking rest
(30) Drive belt
(31) Large belt wheel
(32) Small belt wheel
(33) Handle (insulated gripping surface)
(34) Adapter for changing from HSS to TC planer blades
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Planer
Article number
Rated power input
No-load speed
Cutting depth
Rebate depth
Max. planing width
Weight according to EPTA Pro-
cedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Fitting
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Choosing the Planer Blade
The power tool can be fitted with different planer blades.
Fitting the adapter (34) (accessory) allows the power tool to
be changed from HSS planer blades (15) to HM/TC planer
blades (20).
Always change both planer blades – replacing just one blade
will create an imbalance that could cause vibrations and
shorten the service life of the power tool.
Changing the HSS Planer Blades
Take care when changing the planer blade. Do not pick
u
up the planer blade by the cutting edges. You may be
injured by the sharp cutting edges.
Removing the Planer Blades (see figures A–C)
– To replace the planer blades, turn the blade head (13)
until the clamping jaw (12) is parallel with the planer base
plate (8).
– Undo the three fastening screws (11) using the Torx key
(10) and remove the clamping jaw (12).
– Push the retaining clip (16) together with the planer
blade (15) out of the blade head (13) and/or the guide
groove (14).
1 609 92A 4E6 | (14.09.2018)
– Turn the blade head 180° and remove the second planer
blade.
Note: Before changing or resharpening the planer blades,
remove the retaining clip (16) by undoing the fastening
screw (17).
Resharpening HSS Planer Blades (see figure D)
Worn or blunt HSS planer blades can be resharpened using
A)
the sharpening aid (18) (accessory) and a commercially
available grinding stone.
Place both planer blades in the sharpening aid and clamp
them firmly with the wing bolt. Make sure that both planer
blades are pushed in fully.
Move the planer blades placed in the sharpening aid steadily
GHO 6500
across the grinding stone, applying light pressure.
0 601 596 0..
Note: The planer blades must not be resharpened by more
than 6 mm (i.e. to a minimum width of 23 mm). Both planer
W 650
blades must be replaced when they reach this size.
rpm 16,500
Fitting the Planer Blades (see figures E–F)
mm 0–2.6
Before putting the new or resharpened planer blades (back)
mm 0–9
in, clean the blade head (13) and, if necessary, the planer
mm 82
blade (15) and the retaining clip (16). If the planer blades
are very gummy, clean them with ethanol or petroleum.
kg 2.8
Note: New and resharpened planer blades must always be
set to the correct height before fitting.
/II
The setting gauge (19) is used to set the height of the planer
blades. Place the planer blade (15) and the retaining clip
(16) on the setting gauge. Make sure that the retaining clip
(16) slots into the groove provided. Push the planer blade
(15) against the guide and hold the retaining clip (16) in this
position with the fastening screw (17). This will apply the
correct height setting automatically.
The planer blade must be fitted and aligned with the centre
of the planer base plate (8). Then tighten the three fasten-
ing screws (11) using the Torx key (10), following the tight-
ening sequence (①②③) specified on the clamping jaw
(12).
Note: Check that the fastening screws (11) are firmly
tightened before start-up. Turn the blade head (13) by hand
and ensure that the planer blades are not brushing against
anything.
Changing the HM/TC Planer Blades
Take care when changing the planer blade. Do not pick
u
up the planer blade by the cutting edges. You may be
injured by the sharp cutting edges.
Use only original Bosch HM/TC planer blades.
Hard metal (HM/TC) planer blades have two cutting edges
and can be turned. If both cutting edges become blunt, the
planer blades (20) need to be changed. HM/TC planer
blades must not be resharpened.
Removing the Planer Blades (see figures G–H)
– To turn or replace the planer blades, turn the blade head
(13) until the clamping jaw (12) is parallel with the planer
base plate (8).
Bosch Power Tools