General Safety Instructions; Behaviour In An Emergency Situation; Description Of Device / Spare Parts - ATIKA GTC 40-305 Notice Originale

Risk of injury! Before starting the engine, make sure
•
that your hands and feet are kept at a safe distance to the
cutting tool.
Risk of injury! The cutting tool may after-run. Do not
•
try to slow it down by hand.
• Start cutting only when the cutting tool has reached the full
rotational speed.
• Do not overload the machine! You work better and safer in
the given performance range.
• Take breaks when working so that the motor/battery can
cool down.
• Take breaks when working so that the motor/battery can
cool down.
• Do not place a hot machine in dry grass or onto inflammable
objects.
• Never bring the cutting tool in contact with rigid objects
(stones, trunks).

General safety instructions

• Stop the machine and remove the battery when:
the cutting tool comes in contact with stones, nails or
−
other foreign objects, to check the device for damages
carrying out repair works
−
maintenance and cleaning
−
removing malfunctions and blockages
−
check if the unit starts to vibrate excessively
−
transport and storage
−
replacing the cutting tool
−
Leaving the machine (also during temporary interruption)
−
• Do not touch dangerous moving parts before the battery has
been pulled out of the device and such moving parts have
come to a standstill.
• Maintain the machine carefully:
Follow the maintenance instructions and the instructions
−
for tool exchange.
Keep the handholds dry and free from resin, oil and
−
grease.
• Always keep the machine including tool in a good condition.
• Make sure to check the machine before any use and after
dropping or other impacts to ensure that it is in a proper
condition.
• Check the machine for possible damage:
Before further use of the machine the safety devices must
−
be checked carefully for their proper and intended
function. Only operate the device with complete and
correctly attached safety equipment and do not alter
anything on the device that could impair its safety. Only
operate the machine with complete and correctly attached
safety equipment and do not alter anything on the
machine that could impair the safety.
Check whether the movable parts function perfectly and
−
do not stick or whether the parts are damaged. All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation.
Damaged guards and parts must be properly repaired or
−
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible security labels have to be replaced.
−
18
• Do not allow any tool key to be plugged in!
Before switching on, check always that all tools are
removed.
• Store unused equipment in a dry, locked place out of the
reach of children.
• Note that a failure to maintain the unit properly, any use of
non-conform spare parts or a removal / modification of
safety devices can result in damages to the machine and to
serious injuries of the person who works with it.
Do not carry out repair operations on the machine
other than those described in section "Maintenance
and care" but contact the manufacturer or authorized
customer service centre.
Use only original spare parts and accessories.
Accidents can arise for the user through the use of
other spare parts. The manufacturer is not liable for
any damage or injury resulting from such action.

Refer to the respective "Operating instructions" for notes
on the "Safety" of the battery and the charger.

Behaviour in an emergency situation

• Initiate all required first aid measures suited for the injury
and seek qualified medical advice as quickly as possible.
• Protect the injured person against further injuries and
immobilise the injured person.


Description of device / Spare parts

 Please refer to the attached assembly and operating
instruction sheet.
Pos. Denomination
1 Cutting head
2 Protective hood
3 Protection bow
4 Adjusting knob (Angle adjustment)
5 Lawn trimmer – lower part
6 Front handle
7 Locking nut
8 Lawn trimmer – upper part
9 ECO button
10 Charging unit 1.8 A (ALG 40-1800)
11 Battery 2.0 Ah (AP 40-2000)
12 Battery 4.0 Ah (AP 40-4000)
13 Locking knob
14 ON-OFF switch
15 Cutting thread
16 Thread knife
17 Spool cover
18 Thread spool roll
19 Spool lower part
20 Safety label 1
21 Safety label 2
22 Operating handle
23 Replacement spool
Order-No.

380707
380708






365500
365501
365503




380706


380704
380703

380705