EN Application sheet
CONTROL OF KAMILLA sensor
KITCHEN HOOD
The kitchen hood has 3 ventilation speeds. You
may select low, medium or high ventilation level
depending on the intensity of evaporation during
cooking or frying.
For more efficient air purification, switch on the
stove and the kitchen hood simultaneously. It will
make the ventilation process more efficient. Let
the kitchen hood work for some time after you fin-
ish cooking; thus you will get rid of vapor and un-
desirable smells in the kitchen.
There is a sensor switch of engine and lights work-
ing modes on the front kitchen hood panel (See
Fig. 6a).
1. Switching the kitchen hood on/off.
2. Reduction of ventilation speed.
3. The kitchen hood display shows the number of
ventilation speed, whether the switch-off timer
is on or off, information on polluted filters.
4. Increase in ventilation speed.
5. Switching on/off the kitchen hood switch-on
timer.
6. Switching on/off the lighting.
By using the switches on the panel by slightly
touching the relevant character, you can switch on
any of the three engine speeds in any order, switch
off the lighting or activate the Timer function. The
number of selected speed is shown on the display
(3). The timer is activated by touching the symbol
of the clock on the kitchen hood control.
Timer activation is signaled by the blinking figure
of the selected speed number on the display. 15
minutes after timer switch-off, the kitchen hood
stops working automatically. This function is very
convenient for removal of residual smell from the
kitchen after the food has been cooked.
Lights may be switched on regardless of whether
the engine is working. Your kitchen hood has halo-
gen lamps with lighting regulation. It makes it pos-
sible to select the level of lighting that is comfort-
able for you. To realize this function, put your finger
on the symbol of lights for a long time. The level
of lighting will gradually reduce. After reaching the
minimum level, it will start to gradually increase.
You can stop regulating the symbol of lights at any
KITCHEN HOODS
moment that conforms to the level of lighting you
selected.
Function of control over aluminum
The sensor 3-speed switch has the function of
"control over pollution of aluminum grease trap
filter." After 60 hours of kitchen hood function-
ing, display 3 will show the C symbol that warns
about the necessity to clean the aluminum grease
trap filter. After filter cleaning (see the paragraph
"Maintenance and Servicing of the Kitchen Hood")
and its installation into the kitchen hood, press
button 1 and hold it up to 10 seconds. After this,
symbol C will disappear, and symbol E will appear
on the display, which means that the kitchen hood
is ready for normal functioning again.
INSTRUCTIONS ON THE USE OF
The kitchen hood is to be used for extraction of
smells from the kitchen. It may work in two modes
depending on the method of its installation:
— mode of air removal into the air shaft;
— recirculation mode.
In the mode of air removal into the air shaft (see
Fig. 7), the kitchen hood is connected to the air
shaft with the help of a corrugated hose or a plas-
tic air conduit. Thus, all the evaporations from the
kitchen, smells, char and soot pas through reus-
able aluminum grease trap filters and are removed
outside the premises. With this working mode, it is
not necessary to install charcoal acrylic scent-trap
filters. Extraction mode is the most efficient as the
kitchen hood removes all the evaporations from
the kitchen to the air shaft.
In the recirculation mode (see Fig. 8), the kitch-
en hood is not connected to the air shaft, and thus
the air is just passed through the kitchen hood in-
side the kitchen.
In this mode, charcoal acrylic disposable scent-
trap filters should be installed on the kitchen hood.
These filters are not included in the set and are
bought separately. The use of the kitchen hood in
the recirculation mode reduces its productivity.
We recommend using the kitchen hood in the
mode of air extraction to the air shaft.
filter pollution
THE KITCHEN HOOD
11