Ryobi RY18SFX35A Traduction Des Instructions Originales page 5

WARNING
Do not touch moving hazardous parts before the product
is disconnected from the power supply and the moving
hazardous parts have come to a complete stop.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fi re, personal injury, and product
damage due to a short circuit, never immerse your
tool, battery pack or charger in fl uid or allow a fl uid to
fl ow inside them. Corrosive or conductive fl uids, such
as seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a short
circuit.
OVERLOAD PROTECTION DEVICE
The product has an overload protection device. When
overloading is detected, the product will automatically
switch off. If the overload protector is actuated, the motor
must be allowed to cool down for 5 to 10 minutes.
Turn off the product and disconnect it from the power
supply. The tines are sharp; wear heavy-duty gloves before
touching. Make sure thar the tines can rotate freely and is
not jammed or tight.
When the motor has cooled down, connect the plug to
the power supply and turn on the product. Press the start
button and then the on-off button to start the product. If the
product will still not start, have the product serviced by an
authorised service centre only.
GENERAL SCARIFYING TIPS
■ Adjust the cutting depth according to the needs of your
lawn and the length of the grass.
■ Mow your lawn and apply moss killer a week before you
plan to scarify if your lawn has a moss problem.
■ Water your lawn a few days before scarifying to make
sure your lawn is moist but not overly wet.
TRANSPORTATION AND STORAGE
■ Clean all foreign materials from the product. Store the
product in a cool, dry, and well-ventilated place that
is inaccessible to children. Keep away from corrosive
agents such as garden chemicals and de-icing salts.
Do not store outdoors.
■ For transportation, secure
movement or falling to prevent injury to persons or
damage to the product.
WARNING
Use extreme caution when lifting or tilting the product for
maintenance, cleaning, storage, or transportation. The
tines are sharp, keep all body parts away from the tines
while it is exposed.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps
or tape. Do not transport batteries that are cracked or
leaking. Check with the forwarding company for further
advice.
MAINTENANCE
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause injury, can contribute to poor performance, and
may void your warranty.
Servicing requires extreme care and knowledge
and should be performed only by a qualifi ed service
technician. Have the product serviced by an authorised
service centre only. When servicing, use only original
replacement parts.
■
■
■
■
■
■
■
the product against
■
■
WARNING
WARNING
When the product is stopped for servicing, inspection,
or storage, or changing an accessory, turn off the
power source, disconnect the product from the supply
and make sure that all moving parts have come to a
complete stop. Allow the product to cool down before
making any inspections and adjustments. Maintain the
product with care and keep it clean.
Check the debris collector frequently for wear, holes or
deterioration.
You may make adjustments and repairs described in
this manual. For other repairs, contact an authorised
service centre.
Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
After each use, clean the product with a soft, dry cloth.
Any part that is damaged should be properly repaired or
replaced by an authorised service centre.
Check all nuts, bolts, and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition.
Be careful during adjustment of the product to prevent
entrapment of the fingers between moving tines and
fixed parts of the product.
When servicing the tine assembly, be aware that even
though the power source is turned off, the tine assembly
can still be moved.
The tines on the product are sharp. Use extreme
caution and wear heavy-duty gloves when fitting,
replacing, cleaning or checking bolt security.
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
English | 3