OPerATION
settings
To access the configuration menu, press and hold "Menu". After
approx. 3 seconds, actual value I1 is displayed.
Use "+" and "–" to switch between the individual actual values,
time programs and parameters.
To exit the configuration menu, press "Menu". The standard dis-
play appears.
5.4.1 Actual values
The following actual values can be called up:
display
description
I1
Actual room temperature
I2
Relative heating time
(The counter can be reset via parameter P5.)
Note
The counter for relative heating time (I2) counts in com-
plete hours how long the appliance heats for. When the
appliance is switched off, any heating phase of less than
60 minutes is not recorded.
5.4.2 Time programs
Three time programs are available. Time programs Pro1 and Pro2
are pre-configured at the factory. Time program Pro3 can be set
according to your individual requirements.
display
description
Pro1
Time program "Daily"
- Repeated: Monday to Sunday
Pro2
Time program "Weekdays"
- Repeated: Monday to Friday
Pro3
Time program "User defined"
- up to 14 comfort phases, freely configurable
Note
To use a time program, select the required time program
from the standard menu (see chapter "Settings / Standard
menu").
Note
Ensure the day of the week and the time are set correctly
when setting the time programs.
Note
The following applies to all time programs (Pro1, Pro2,
Pro3):
If the end time is later than 23:59 h, the end time will
automatically be moved to the next day of the week. The
comfort phase is maintained past midnight and will end
on the next day at the set end time.
Time programs Pro1 and Pro2
You can specify the comfort mode start and end times with time
programs Pro1 and Pro2. During this time period, the appliance
heats to the set comfort temperature. Outside this specified time
period, the appliance operates in setback mode. This results
in a comfort phase and a setback phase, which are repeated
daily (Pro1) or on every working day (Pro2).
www.stiebel-eltron.com
Theses phases are factory-set as follows:
- 08:00 h - 22:00 h: Comfort mode
- 22:00 h - 08:00 h: Setback mode
Note
When time program Pro2 is enabled, the appliance oper-
ates at weekends exclusively in setback mode.
To adapt time programs Pro1 and Pro2 according to your needs,
proceed as follows:
f In the configuration menu, use "+" and "–" to call up the re-
f
Unit
quired time program.
[°C] | [°F]
[h]
f Press "OK".
f
The start time for comfort mode is displayed.
f Use "+" and "–" to set the required start time.
f
f Press "OK".
f
The end time for comfort mode is displayed.
f Use "+" and "–" to set the required end time.
f
f Press "OK" to save.
f
Time program Pro3
You can use time program Pro3 to specify up to 14 separate com-
fort phases which are repeated weekly.
To configure a comfort phase in time program Pro3, proceed as
follows:
f In the configuration menu, use "+" and "–" to call up time
f
program Pro3.
f Press "OK".
f
The display shows "3---".
f Press "OK".
f
A day of the week or a group of days is displayed.
f Use "+" and "–" to select the required day or group of days.
f
f Press "OK".
f
The start time for comfort mode is displayed.
f Use "+" and "–" to set the required start time.
f
f Press "OK".
f
The end time for comfort mode is displayed.
f Use "+" and "–" to set the required end time.
f
f Press "OK".
f
Comfort phase "3-01" has been configured.
f To configure a further comfort phase, use "+" and "–" in time
f
program Pro3 to select display "3---". Proceed as describe
above.
Note
To reset the selected comfort phases, activate parame-
ter P4.
f Please note that activating parameter P4 resets all
f
time programs (Pro1, Pro2, Pro3) to the factory set-
ting.
CON Premium | CON Premium U |
21