Electrical Safety; Before The First Start-Up - ATIKA UZT 250 Mode D'emploi

− Damaged guards and parts must be properly repaired or
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
− Damaged or illegible safety labels should be replaced
immediately.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and adjust-
ing tools are removed.
Store unused equipment in a dry, locked place out of the
reach of children.

Electrical safety

Extension cable to be designed in compliance with IEC 60
245 (H 07 RN-F) having a core cross-section of at least:
1.5 mm² for cable lengths up to 25 m
2.5 mm² for cable lengths over 25m
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, non-rigid PVC or other thermoplastic mate-
rial of same mechanical stability or be covered with this ma-
terial.
Protect yourself against an electric shock. Avoid touching
earthed parts with your body.
The connector of the connection cable must be splash-
proof.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the cable and if damaged, have it renewed
by a recognised skilled electrician.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Regularly check the extension cables and replace them if
they are damaged.
Do not use any defective connection cables.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current cir-
cuit breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or
one of our customer service points. Local regulations – es-
pecially regarding protective measures – must be ob-
served.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not li-
able for any damage or injury resulting from such action.
Assembling
1. Adjust the saw blade to its max. cutting height.
2. Loosen the screws of the table section(1) and remove them
3. Slightly loosen the screws (34) and attach the safety guard
(2) as shown in figure
4. Adjust the blade guard (18) as shown in figure
the specified dimensions).
5. Pay attention that the blade guard is aligned with the saw
blade in a straight line.
6. Retighten the screws (34) firmly and reattach the table sec-
tion and the safety guard.
C1 – C3
Mount the extraction hose T-connector (22) to the housing using
2 screws and 2 washers.
Plug the extension piece (21) on the extractor neck on the hous-
ing.
Connect the long extraction hose to the safety guard's extraction
neck and the short one to the extension piece. Connect the
other ends of the extraction hoses to the extraction T-connector.
Fix the short extraction hose using two hose clips (32).
D
Loosen the clamping screw (26) for the universal guide (27) and
slide the guide ruler on the guide carrier (6) and retighten the
clamping screw.
E
If the saw is used without a base frame, the saw must be fas-
tened on a firm workbench with the 4 provided angles and
screws (M6x16).
F
If the saw is used with a base frame, the rubber foots must be
removed before the base frame is attached.

Before the first start-up

To achieve flawless functioning of the machine, please
follow the instructions listed:
Place the saw at a location which meets following conditions:
secured against slipping
free of vibrations
even
free of tripping hazards
adequate light
Before each use, check
Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
that the guard is in a proper condition
the splitting wedge setting (see splitting wedge setting)
the saw blade for flawless condition
whether the push stick is to hand
Do not use any cracked saw blades or such that have
changed their shape.
Do not use any saw blades made of HSS steel.
19
A4
A5 (Observe