Cleaning And Maintenance; Technical Specification - Asist AE2C07DN Mode D'emploi

2. To turn it off, release the on/off switch (5).
Switching on/setting the speed range:
♦ Set the ON/OFF switch with the speed control
to a position between „-a+".
Notes on working with materials/ tools/speed
range
■ Use the milling bits for working on steel and iron at
maximum speed.
■ Determine the rotational speed range for working
on zinc, zinc alloys, aluminium, copper and lead
by trying it out on test pieces.
■ Use a low rotational speed for work on plastics and
materials with a low melting point.
■ Use a high rotational speed for working on wood.
■ Carry out cleaning, polishing and buffing work
in the medium speed range. The following are recom-
mendations only and not binding. When carrying out
practical work, carry out your own tests to see which
tool and which settings are ideal for the material you
are working on.
General Work Recommendations
The accessories may break at high speed and pres-
sure. Therefore, apply only low pressure on the tool.
This will ease your work and also prevent wear and
damages of your power tool and the edges. Use only
clean and sharp accessories. Plastics must be pro-
cessed at low speed since they tend to melt during
processing. If vibrations occur, increase the speed.
When working with grinding and polishing tools, use
the settings for low speed. If the tool speed decreases
during processing, it means that most probably you
apply too much pressure on it. Dirty or blunt tools
decrease the efficiency. Clean the attachment if you
notice that you must exert too much pressure on the
power tool..

CLEANING AND MAINTENANCE

! Before cleaning and maintenance, always disconnect
the supply cable from the mains.
Your power tool does not require any additional lubri-
cation or maintenance. No parts that you may repair
are present.
Never use water or chemical agents to clean your
power tool. Wipe it with a dry cloth.
Keep the motor cooling vents clean.
If you notice slight sparkling in the motor area, your
power tool is sound. If the sparkling intensity increas-
es, a motor malfunction is concerned.
Never clean any part of the power tool by a hard, sharp
or rough object.
Store the power tool if not used for a longer period.
Do not store the power tool in places with high tem-
peratures. If possible, store the power tool in a place
with a constant temperature and humidity.

TECHNICAL SPECIFICATION

Power supply
Speed without load
7.2 V DC
5000-25000min-1
Battery
Collet diameter:
Adjust the speed LED
LED work lights
soft handle
Accessories 40 pieces in plastic box
Protection class
electric twist
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 75,8 dB (A) KpA=3
LWA (sound power)
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN 6074
5:
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIRONMENTAL PROTECTIONWASTE MANAGE-
MENT
50
7.2 V DC 1000 mAh, Li-Ion
3.2 mm
86,8 dB (A) KwA=3
2,11 m/s2 K=1.5
III.
IP20