Freezer Compartment Door - SEVERIN KS 9826 Mode D'emploi

∙ The product data sheet contains details of the ambient
temperature range suitable for this appliance.
∙ Do not use the appliance outdoors.
∙ Ensure that the plug is accessible and can be removed from
the wall socket at any time.
∙ Do not expose the appliance to direct sunlight, and do not
position it next to any heat sources (radiators, cookers etc).
If this cannot be avoided, however, suitable insulation must
be in installed between the heat source and the unit.
∙ The unit must not be installed inside a cabinet, nor directly
below a hanging cupboard, shelf or similar object.
∙ Ensure that the door can swing open to an angle of 160°.
∙ In the case of uneven fl oors, the adjustable feet on the unit
can be used to compensate and ensure optimum stability.
Ventilation
Ensure that there is enough space around the unit so that the
air circulation round and behind it is not obstructed. (Rear and
sides 5 cm, top 10 cm.)
Reversible door
If required, the door may be reversed, i.e. from right-hinged (default
installation) to left-hinged.
Warning: Always disconnect the unit from the mains before
any maintenance or repair work is carried out.
1. Remove the two screw covers (11) and the screws (10).
2. Remove the entire top panel (9).
3. Remove the three threaded bolts (6) securing the upper
hinge plate (5) on the right-hand side.
4. Carefully lift up the door and place it on a suitable surface
to protect it from scratches.
5. Take off the protective corner-piece (7) and re-fi t it in the
groove on the right-hand side, pushing it fi rmly down.
6. Remove the hinge pin from the upper hinge plate (5) and
screw it back in from the opposite side.
7. Remove the two screws from the left-hand side in the
upper hinge plate mounting and re-fi t them on the right.
8. Remove the three screws (1) holding the lower hinge plate
12
(2) on the right-hand side.
9. Remove the hinge pin from the lower hinge plate and re-fi t
it in the next hole.
10. Remove the adjustable foot (4) from the left-hand side and
re-fi t it on the right.
11. Attach the lower hinge plate (2). Do not tighten the screws
for the moment.
12. Replace the door in its new position. Ensure that the hinge
pin is inserted into the guide bushing (hole) on the lower
part of the door frame.
13. Attach the upper hinge plate (5) (removed earlier in step 3)
on the left-hand side. Ensure that the hinge pin is inserted
into the guide bushing (hole) on the upper part of the door
frame. Do not tighten the screws for the moment.
14. Adjust the closed door to its proper position and tighten
the screws of the upper and lower hinge plates.
15. Replace the top panel (9).
16. Replace the screws (10) und the screw covers (11) in the
top panel (9).
17. Put the unit back in its intended position and wait for about
two hours before connecting it to the mains.

Freezer compartment door

1. Open the door
2. Insert a screwdriver into the slot under the lower hinge,
push the spring up and hold it.
3. Remove the door and hinge assembly.
4. Take off the protective cover from the left-hand side and
re-fi t it in the opening on the right-hand side.
5. Turn the door round 180°, place the lower hinge onto the
lower door pin and insert the upper door pin into the upper
hinge.
6. Now slide the lower hinge into the corresponding opening,
ensuring it locks into place.
Temperature control
The unit is re-activated by
connecting it to the mains. It
is only switched off completely
when the plug is removed from
the wall socket.
The temperature in the refrigerator cabinet can be adjusted by
setting the temperature control. Turning the control clockwise
will decrease the temperature, while turning it anti-clockwise
will increase it.
∙ After switching on, the temperature control should be set to
its maximum setting.
∙ After 30 minutes, the setting should be changed to a
medium setting, usually suffi cient for home use.
Following a power interruption, or if the unit has been switched
off on purpose, it may take 3 to 5 minutes before it switches
on again.
In position '0', the cooling function is switched off, though
the appliance is still connected to the mains.
Interior lighting
Changing the light bulb:
∙ Remove the plug from the wall socket.