Safety Systems; Main Technical Data - Nilfisk SWEEPER SR 1450 B-D Manuel D'utilisation

Dashboard
Fitted on the upper part of the frame and under the steering
wheel, the dashboard houses the machine warning lights and
instrumentation.
Hydraulic system
In the first circuit a variable delivery pump feeds the drive
hydraulic motor (rear wheel). In the second circuit a gear
pump feeds a lever double-acting distributor. The distributor
operates the lifting cylinders and the broom motors. All
circuits are protected by suction filters and safety valves.
Electrical system
SR 1450 D: 12 V electrical system supplied by an alternator
operated by the engine. The circuits are protected by lamellar
fuses housed in a relevant fuse box.
SR 1450 B: power electrical system supplied by a 36 V
battery. The service electrical system is supplied by a 12 V
power supply. The circuits are protected by lamellar fuses
housed in a relevant fuse box.
Stability
Machine stability depends on the conditions in which it is
used.
If the machine is used within the conditions of use specified in
the manual, it is stable. To this end, the following tests were
carried out under the same conditions on a prototype identical
to the series model and no stability problems arose. The
conditions were:
Flat ground with good surface conditions:
– Transfer maximum speed: 13 km/h (SR 1450 D)
Transfer maximum speed: 8 km/h (SR 1450 B)
– Working speed: from 1 to 8 km/h
– Bending radius (maximum speed of 12 km/h): 3 m (SR
1450 D)
– Bending radius (maximum speed of 7 km/h): 3 m (SR
1450 B)
– Bending radius (speed of 5 km/h): 0 m
On sloping ground with good surface conditions and
maximum longitudinal slope of 20%:
– Bending radius (maximum speed of 5 km/h): 3 m
– Bending radius (speed of 1 km/h): 0 m
Maximum crossfall while in transfer: 15%.
Maximum crossfall at 5 km/h: 20%.
The tests were carried out with lowered and empty hopper.
For different conditions of use, the machine operator should
be able to assess the limits of the machine and should, in any
case, follow the indications laid down in the manual.
33014811(1)2005-07 A
Information on brooms
Side brooms (2, Fig. E)
– Polypropylene side broom
– Polypropylene and steel side broom
– Steel side broom
– Nylon side broom
Main brooms (12, Fig. E)
– Natural fibre and polypropylene main broom
– Polypropylene main broom
– Polypropylene and steel main broom
– Nylon main broom
Brooms with a moplen shaft or with different bristles can be
supplied on request.

SAFETY SYSTEMS

The machine is provided with an operator's seat sensor that
stops the machine as soon as the operator leaves the seat.

MAIN TECHNICAL DATA

SR 1450 D
General data
Weight in running conditions (without
operator)
Length
Width
Height
Speed
Gradeability
Sweeping range (main broom only)
Sweeping range with one side broom
Sweeping range with two side brooms
Side broom diameter
Main broom length
Hopper capacity
Hopper maximum load
Dumping height
Filtering system
Diesel engine
Tyres
Superelastic wheels
Fuel tank
Hydraulic tank
Engine oil pan capacity
Transmission
Steering
Brake
Parking brake
Sweeping system
Controls
USER MANUAL
Values
720 Kg
1,880 mm
1,170 mm
1,470/2,230 mm
0/13 Km/h
16%
800 mm
1,150 mm
1,450 mm
550 mm
800 mm
115 litres
120 Kg
0/1,420 mm
5 m
Lombardini Focs
LDW 702
3.00/8
3.00/8
10 litres
32 litres
1.6 litres
Hydrostatic
Mechanical
Hydraulic
Mechanical
Self-levelling device
Hydraulic
2
7