Federal Communication Commission Interference Statement; Legal Notices - Dynex DX-WGNBC Guide De L'utilisateur

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

DX-WGNBC_WGDTC_combo.fm Page 7 Wednesday, June 21, 2006 11:53 PM
FCC
FCC
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Important Note (for DX-WGNBC)
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter. This equipment has been SAR-evaluated
for use in laptops (notebooks) with side slot configuration.
Important Note (for DX-WGDTC)
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Dynex declares that DX-WGNBC (FCC ID: MXF-P950529G) is limited in
CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
Dynex declares that DX-WGDTC (FCC ID: MXF-P950605G) is limited in
CH1~CH11 for 2.4 GHz by specified firmware controlled in U.S.A.
IC statement (for DX-WGDTC)
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
This device has been designed to operate with an antenna having a
maximum gain of 5 dBi. Antenna having a higher gain is strictly
prohibited per regulations of Industry Canada. The required antenna
impedance is 50 ohms.
Important Note
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator & your
body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IC statement (for DX-WGNBC)
IC statement
Operation is subject to the following two conditions: (1) This device may
not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Important Note
IC Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for
an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. This
transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

Legal notices

© 2006 Dynex. DYNEX and the DYNEX logo are trademarks of Best Buy
Enterprise Services, Inc. Other brands and product names are trademarks
or registered trademarks of their respective holders. Specifications and
features are subject to change without notice or obligation.
7

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Dx-wgdtc

Table des Matières