Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
The following table shows the display of these 4 switches
and their corresponding DiSEqC commands
LED Display
DiSEqC 1.0 Switch
„LNB"
„+/-"
OPT(1)
SAT
Tone Burst POL 22KHz DiSEqC
Taste
Taste
1
H _
1
A
(0) = OFF
1
H 2
1
A
(0) = OFF
1
U_
1
A
(0) = OFF
1
U 2
1
A
(0) = OFF
1 C
H _
1
B
(1) = ON
1 C
H 2
1
B
(1) = ON
1 C
U _
1
B
(1) = ON
1 C
U 2
1
B
(1) = ON
2
H _
2
A
(0) = OFF
2
H 2
2
A
(0) = OFF
2
U _
2
A
(0) = OFF
2
U 2
2
A
(0) = OFF
2 C
H _
2
B
(1) = ON
2 C
H 2
2
B
(1) = ON
2 C
U _
2
B
(1) = ON
2 C
U 2
2
B
(1) = ON
Note:
1 OPTIONAL is one the 4 committed switches of DiSEqC 1.0. It is allocated for the
use of the third LNB switching, or, driving of a simple positioner. Consult your
dealer for details of installation and application.
2 Normally, the DiSEqC 1.0 device does not require the Tone Burst to make satellite
selection. This Tone Burst is provided for backward compatibility. You can still
use your old Tone Burst switch for satellite selections
Ausgangs-Signal
DiSEqC-LNB
Schalter
H
OFF
H
ON
SAT 1
HORI
V
OFF
VERT
V
ON
HI/LO BAND
H
OFF
H
ON
SAT 2
HORI
V
OFF
VERT
V
ON
HI/LO BAND
H
OFF
H
ON
SAT 3
HORI
V
OFF
VERT
V
ON
HI/LO BAND
H
OFF
H
ON
SAT 4
HORI
V
OFF
VERT
V
ON
HI/LO BAND
20
IF Frequency
Press „SET" key for 2nd time. and the reading of the IF frequency is shown on the
display. This can be tuned up or down with „ +" / „ -" keys, or entered with
„ 0" - „ 9" digit k The IF frequency is calculated based on the following:
IF = SATELLITE TV FREQUENCY - LNB L.O. FREQUENCY
Example : Your LNB is with L.O. frequency : 11.475Ghz, If
you want to view the WDR (12.658 GHz) on
Kopernikus, then, set the IF frequency to :1183 = 12.658 - 11.475
enter the frequency directly with key sequence
„1"
„1"
„8"
„3"
After selection, press „ENT" key to exit and store the new setting in the memory.
Audio Mode and Audio (L) Frequency
- Press „SET" key for 3rd time and the display shown :
Audio mode and frequency :
- Press „AUDIO" key to select between 5 modes of audio reception.
Display
mode
audio band
S.X.XX
stereo
narrow
L.X.XX
mono
narrow
A.X.XX
J.X.XX
C.X.XX
The correct audio frequency can be set by the „ + /-" key or entered directly
with „0" - „9" key.
Example : Audio frequency is 7.02 MHz. enter directly with „7"
Exit and Store
Press „ENT" key to exit and store the new programming.
Press „SET" key again to exit the set mode and the
new programming will not be stored in the memory
deemphassis
DNR
DNR
„0"
„".
21
Publicité
Chapitres
Table des Matières
