Safety Instructions - ATIKA ALA 2800 Notice Originale

S a f e t y
S a f e t y
Before commissioning this product, read and keep to
the following advice. Also observe the preventive regula-
tions of your professional association and the safety provi-
sions applicable in the respective country, in order to pro-
tect yourself and others from possible injury.
Pass the safety instructions on to all persons who work
with the machine.
Keep these safety instructions in a safe place.
Repair works on the shredder must be carried out by
the manufacturer or by companies appointed by the
manufacturer respectively.
Make yourself familiar with the equipment before using it, by
reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see 'Nor-
mal intended use' and 'Working with the garden shredder').
Provide a safe standing position and keep at any time the
balance. Do not lean forward. When placing material into
the shredder, always stand on the same level as the ma-
chine. When placing material into the shredder, always
stand on the same level as the machine.
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or un-
der the influence of drugs, alcohol or medicaments. One
moment of carelessness when using the device can result in
serious injuries.
Wear protective goggles, gloves and noise protection while
working with the machine.
Wear suitable work clothes:
- do not wear loose-fitting clothes
- slip-proof shoes
Within his area of work the operator is responsible for third
parties.
The machine must not be operated by children or young
people under 16 years of age.
Keep children away form machine.
Never operate the machine if other persons are in the im-
mediate vicinity.
Never leave the device unattended.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Choose a working position alongside the equipment or
behind it. Never stand near the ejection opening.
Never reach into the filling or ejection opening.
Keep your face and body away from the filling opening.
Do not overload the machine! You work better and safer in
the given performance range.
Only operate the machine with complete and correctly at-
tached safety equipment and do not alter anything on the
machine that could impair the safety.
Do not alter the revolution speed of the motor, since this
controls the safe maximum operating speed, and protects
the motor and all rotating parts against damage due to ex-
cess speed.
Do not operate without the funnel.
Do not modify the device or parts of the device respective-
ly.
Close machine properly before enabling motor.
12
i n s t r u c t i o n s
i n s t r u c t i o n s
Do not hose down the device with water. (Origin of danger
electric current).
Take into consideration environmental influences:
Do not use the device in moist or wet ambience.
−
Do not leave the machine standing in the rain or use
−
when raining.
Provide for good illumination.
−
To prevent danger of injury to fingers during assembly or
cleaning operations wear protecting gloves.
Switch the machine off and remove the mains plug from
the socket when
Performing maintenance and cleaning
−
work.
Eliminating faults.
−
Checking connecting lines, whether these
−
are knotted or damaged.
Transporting.
−
Carrying out repair work.
−
Leaving unattended (even during short interruptions).
−
If the machine's filling funnel or ejection slot is blocked
switch off the motor and disconnect the mains plug before
removing material from the filling funnel or ejection slot.
Check the machine for possible damage:
Before further use of the machine the safety devices
−
must be checked carefully for their proper and intended
function.
Check whether movable parts function perfectly and do
−
not stick or whether parts are damaged. All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
Damaged safety devices and parts must be properly
−
repaired or exchanged by a recognized, specialist work-
shop; insofar as nothing else is stated in the instructions
for use.
Damaged or illegible safety labels have to be replaced.
−
Store unused equipment in a dry, locked place out of the
reach of children.
E l e c t r i c a l s a f e t
E l e c t r i c a l s a f e t
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-section of at least
1.5 mm for cable lengths up to 25 m
2
−
2.5 mm for cable lengths over 25 m
2
−
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be
made of rubber, plasticised PVC or other thermoplastic ma-
terial of same mechanical stability or be covered with this
material.
The connector of the connection cable must be splash-
proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges. Do
not use the cable to pull the plug from the socket.
Regularly check the extension cables and replace them if
they are damaged.
y
y