Singercon CON.LMH-1/30/WHB Manuel D'utilisation page 5

EN
e) Please keep this manual available for future reference.
If this device is passed on to a third party, the manual
must be passed on with it.
f) Keep packaging elements and small assembly parts in
a place not available to children.
g) Keep the device away from children and animals.
h) If this device is used together with another
equipment, the remaining instructions for use shall
also be followed.
2.3. PERSONAL SAFETY
a) Do not use the device when tired, ill or under the
influence of alcohol, narcotics or medication which
can significantly impair the ability to operate the
device.
b) The device is not designed to be handled by persons
(including children) with limited mental and sensory
functions or persons lacking relevant experience and/
or knowledge unless they are supervised by a person
responsible for their safety or they have received
instruction on how to operate the device.
c) The device can be handled only by physically fit
persons who are capable of handling it, properly
trained, familiar with this manual and trained within
the scope of occupational health and safety.
d) The device is not a toy. Children must be supervised
to ensure that they do not play with the device.
2.4. SAFE DEVICE USE
a) Disconnect the device from the power supply
before commencement of adjustment, cleaning and
maintenance. Such a preventive measure reduces the
risk of accidental activation.
b) When not in use, store in a safe place, away from
children and people not familiar with the device who
have not read the user manual. The device may pose
a hazard in the hands of inexperienced users.
c) Keep the device in perfect technical condition. Before
each use check for general damage and especially
check for cracked parts or elements and for any other
conditions which may impact the safe operation of
the device. If damage is discovered, hand over the
device for repair before use.
d) Keep the device out of the reach of children.
e) Device repair or maintenance should be carried out
by qualified persons, only using original spare parts.
This will ensure safe use.
f) Avoid situations where the device stops working
during use due to excessive loading. This may result
in overheating of the drive elements and damage to
the device.
g) Do not move, adjust or rotate the device in the course
of work.
h) Do not leave this appliance unattended while it is in
use.
i) Clean the device regularly to prevent stubborn grime
from accumulating.
j) The device is not a toy. Cleaning and maintenance may
not be carried out by children without supervision by
an adult person.
k) It is forbidden to interfere with the structure of
the device in order to change its parameters or
construction.
l) Keep the device away from sources of fire and heat.
m) Do not overload the device.
n) Do not cover the ventilation openings!
8
o) Always move / mount the device holding it by the
base, never by the head!
p) The head heats up during operation. For maintenance,
adjustment, dismantling or transport allow the device
to cool down after switching it off.
ATTENTION! Despite the safe design of the device
and its protection facilities and despite the use of
additional elements protecting the operator, there is
still a slight risk of an accident or injury when using
the device. When using the device stay alert and use
common sense.
3. USE GUIDELINES
The LED moving head is a lighting device intended only
for entertainment, exhibition and architectural purposes.
Not suitable for home lighting. The head can be used as
a standing device or mounted on a lighting ramp.
The user is liable for any damage resulting from
unintended use of the device.
3.1. DEVICE DESCRIPTION
3
2
1
1. The base has a control panel (on the front) and
a power cable and DMX input (on the back)
2. Movable grip
3. The head
3.2. PREPARING FOR USE
APPLIANCE LOCATION
The temperature of environment must not be higher than
40°C and the relative humidity should be less than 85%.
Ensure good ventilation in the room in which the device
is being used. There should be at least 50 cm distance
between each side of the device and the wall or other
objects. Keep the product away from hot surfaces. The
device should always be used when positioned on an
even, stable, clean, fireproof and dry surface, and be out
of the reach of children and persons with limited mental
and sensory functions. Position the device such that you
always have access to the power plug. The power cord
connected to the appliance must be properly grounded
and correspond to the technical details on the product
label.
NOTE: If the devices are mounted on a ramp or other
structure, they must be secured so as make it impossible to
pass directly under the LED heads.
ASSEMBLING THE APPLIANCE
The device can be mounted on a lighting ramp. Before
assembly, make sure that the structure to which the device
will be attached is stable and its carrying capacity is 10
times the weight of the device. To mount the device on
a ramp, screw the connector to the base and screw the
special hook to the connector.
Before turning on, make sure that the assembly is correct
and the screws are tightened securely. When installing
and using the device on a ramp, use a safety cable with
a strength of 12 times the weight of the device.
An example of the correct installation of the LED head on
the lighting ramp:
3.3. DEVICE USE
Note: the device has a memory function. After setting the
desired lighting effect, press ENTER. After the next start, the
device will turn on with the function previously set.
Functions
Addr A001-A512 512 set of addresses
11CH 11 channel mode
CHnd
9CH 9 channel mode
nASt Master mode
SLnd SL1 Mode DMX 512
SL2 Slave mode
SH 0 0 effect (recommended)
SH 1 Effect 1
SHnd
SK 2 Effect 2
SH 3 Effect 3
On Sound control mode on
Soud
Off Sound control mode off
SEnS 0-100 Sound sensitivity adjustment
Without 512 signal, return
bLAc
to zero
Auto Without 512 signal ,auto
bLnd
Soun Without 512 signal, sound
Without 512, saves last
HoLd
status of controller
Closes the screen after 30
OFF
seconds
LEd
ON Screen always open
No View back
diSP
YES View forward
No X dynamo corotation
rPAN
YES Reverse X dynamo rotation
EN
No Y dynamo corotation
rtiL
YES Reverse Y dynamo rotation
rESt YES System reset
11 channel mode
1 Pan running 0-255
2 Pan Fine 0-255
3 Tilt Running 0-255
4 Tilt Fine 0-255
Colour
Colour selection 10-139
5
Automatic colour 140-255
change (from slow to fast)
Gobo
Stationary gobos 8-63
6
Moving pattern 72-127
Automatic pattern 128-255
change (from slow to fast)
7 Strobe 0-255
8 Dimming 0-255
Pan / Tilt movement
9 0-255
speed
Automatic mode
Another channel
0-59
function
10
Automatic mode 60-159
Sound mode 160-255
Pan Running 10-100
Tilt Running 101-200
11
Pan Tilt Running 201-249
Reset 250-255
9 channel mode
1 Pan running 0-255
2 Tilt Running 0-255
Colour
3 Colour selection 10-139
Automatic colour 140-255
change (from slow to fast)
Gobo
Stationary gobos 8-63
4
Moving pattern 72-127
Automatic pattern 128-255
change (from slow to fast)
9