SLV P-LIGHT Mode D'emploi page 3

ENGLISH
OPERATING MANUAL FOR
LUMINAIRE FOR EMERGENCY LIGHTING
240004
Read this short manual carefully and keep it accessible for further
reference!
Technical data
Operating voltage 220-240V
frequency: 50-60Hz
Luminous flux: 100 lm
System power: 6,5W
Circuit mode: Maintained /
non-maintained circuit
Rated operating time: 3 hours
Safety class: II
Type of protection: IP65
Ambient temperature: 0° -+25°C
Battery: NI-CD AA 2*1000mAh 3.6V
Charging current: 80 - 110mA
Recognition distance: 30m
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
 Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
 Do not look directly into the light source.
 The product may not be modified or converted.
 Do not hang or fasten anything on the product, especially no decoration.
 Do not cover the product - provide free air circulation.
 In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
 This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be used with a voltage of 220-240V ~50-60Hz.
 only be installed according to safety class II (two).
 only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
 only be operated on normally or not flammable surfaces.
 only be used in dry condition,
 not in damp or dirt-endangered rooms.
 not in areas of high air humidity.
 not be exposed to strong mechanical loads or to strong contamination.
OPERATION
Automatic test function
After Implementation an automatic test run will be carried out and will be
continued in the following intervals.
 Every 4 seconds: Battery will be checked for contact failure, charging failure
as well as for luminaire and transformer failure.
 Every month: a 3 minutes endurance test.
 Every year: a 1-3 hours endurance test.
Note: All test functions are default settings and should not be adjusted!
Manual test function
Press the test button once
Press the test button twice within 2 seconds
Press the test button three times within 2
seconds
Press the test button four times within 2
seconds
LED status display
Permanently on
green
Flashing
Flashes once, 4 seconds break
Flashes twice, 4 seconds break
Flashes three times, 4 seconds
red
break
Flashes four times, 4 seconds
break
Flashes five times, 4 seconds
break
MAINTENANCE AND CARE
Light source
 The light source of this luminaire may only be replaced by the manufacturer,
an authorized service technician or a comparable qualified person.
Battery
 If the specified operating time of (3h) will not be reached after full charge of
the battery, the battery should be replaced immediately.
Battery replacement
 Unplug the battery plug (1).
 Remove old battery and insert new one .
 Insert plug (1).
.
Care
Disconnect the product from the power supply and let it cool down, before
you clean the product.
 Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
 The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
30 seconds endurance
test
3 minutes endurance test
30 minutes endurance
test
1-3 hours endurance test
Ready / normal operation
Test phase
Check (failure)
Battery not connected
Battery short circuit / low
voltage
Battery charger defect
Transformer defect
LED lamp defect
After a damp or soiling storage the product may only be installed
after checking its condition by an approved electrician.
Disposal (European Union)
 Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive (WEEE,
2012/19) on electrical and electronic devices at local collection points for
such devices!
 Notice on used batteries/accumulators:
Return only fully discharged batteries/accumulators.
Mask the poles during storage and disposal that no short circuits may
occur.
INSTALLATION
(only by an approved electrician)
Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are
loose parts inside the housing and these are not explicitly described the
product may not be installed or operated.
Use the supplied fastening material only when it is suited for the
installation background. If this is not the case use only fastening material
suiting the installation background.
Unpacking
 Carefully take the product out of the packaging removing any transport
safeguards.
 Before disposal of the packaging material make sure that all components
of the product are removed.
Installation place
Installation place
 The product is solely suited for recessed wall- and ceiling installation.
 The product is solely suited for installation on the wall and ceiling.
Installation steps (read completely before installation)
 Install the luminaire as shown in the figure.
 Electrical Connection
 Secure the cable screwing using a suitable tool
 The product must be able to be separated by an all pole separation
from the current supply.
 For electric connection attach the black or brown wire (live conductor)
of the connection lead with the clamp L and the blue wire (neutral
conductor) of the connection lead with the clamp N.
 If the luminaire will be used as a non-maintained luminaire (lamp is
only operating in case of power failure), the bridge between clamp SL
and L must be removed. (2).
Check if the product functions properly and is securely fixed!
art.-no. 240004 © 28.06.2016 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.