Troubleshooting - Maytag W10649235C Guide D'utilisation Et D'entretien

TROUBLESHOOTING

First try the solutions suggested here or visit our website at www.maytag.com/product_help –
If you experience
Error Code Appears in Display
Once any possible issues are corrected, touch POWER/CANCEL once to clear the code. Reselect and restart the cycle.
"Sd"
(Excess suds)
appears in display
Lo followed by FL or F8
followed by E1 (water
supply error) appears in
display
F9 followed by E1
(drain pump system
error) appears in display
F5 E2
followed by
(door will not lock)
appears in display
"rL"
(remove load)
appears in display
Washer making error
beeps
Washer beeps when
START is touched
F# E#
code other
than as described above
appears in display
"nt" (interrupted)
appears in display
Clean Washer LED
flashing at end of wash
cycle
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Possible Causes
Excessive suds in washer. Washer is
running a suds reduction routine.
Check for proper water supply.
Check plumbing for correct drain
hose installation. Drain hose extends into
standpipe farther than 4 ⁄ " (114 mm).
1
2
Not using HE detergent or using too
much HE detergent.
Washer door not locking.
Load detected in drum during Clean
Washer with affresh cycle.
®
Door has not been opened and closed
for at least 3 cycles.
Door not closed.
System error code.
The cycle was paused or cancelled.
The washer has run 30 wash cycles and
is indicating a reminder to run the Clean
Washer with affresh cycle.
®
Allow the washer to continue. Use only HE detergent. Always
measure detergent, and base detergent quantity on load size.
Follow detergent manufacturer's instructions.
Unit will drain for 8 minutes while door remains locked. When
complete, touch POWER/CANCEL once to clear the code. Then
touch POWER/CANCEL again to restart washer. If code appears
again, call for service.
Both hoses must be attached and have water flowing to the inlet
valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
If used, auto shut off connectors and hoses must be properly
installed and in working order.
Check drain hose for proper installation.
Make sure the drain hose is not kinked, pinched, or blocked.
Remove any clogs from drain hose.
Use drain hose form and securely attach to drainpipe or tub.
Lower drain hose if the end is higher than 96" (2.4 m) above
the floor.
Use only HE detergent. Always measure detergent and follow
manufacturer's directions based on load size and soil level.
Touch POWER/CANCEL to cancel the cycle. Make sure the door
is closed completely and latching. Check for items in the washer
drum that may be keeping the door from closing completely.
Remove items from washer drum and restart Clean Washer with
affresh cycle.
®
This code may appear when the washer is first turned on.
Open and close the door to clear the display.
Close the door completely.
Touch POWER/CANCEL once to clear the code. Then touch
POWER/CANCEL again to restart washer. If code appears again,
call for service.
The washer can take 20 to 30 minutes to stop spinning and drain
and will display this error code during that time. Touch POWER/
CANCEL once to clear the code. Then touch POWER/CANCEL
again to restart washer.
Run the Clean Washer with affresh
with affresh cycle is not turned on, the LED will stop flashing at
®
the end of a wash cycle after running 3 more regular wash cycles.
After 30 more wash cycles are completed, the Clean Washer LED
will again flash at the end of a wash cycle as a reminder.
Solution
cycle. If the Clean Washer
®
15