Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Channel Mode
Press the MENU button until
is
shown on the display.
Press the ENTER button so the display
starts blinking.
Use DOWN and UP button to select the
(15 Channel) or
(8 Channel)
mode.
Once the mode is selected, press the
ENTER button to setup
(Or
automatically
return
to
the
main
functions
without
any
change
after
8
seconds.)
To go back to the functions without any
change press the MENU button again.
Show Mode
Used to choose the Show mode when used
in standalone or master/slave mode.
Press the MENU button until
is
showing on the display.
Press the ENTER button, the display starts
blinking.
Use DOWN and UP buttons to select
(show 1),
(show 2),
(show 3) or
(show 4) mode.
Once the right mode shows on the display,
press the ENTER button to save it.
(or automatically return to the main functions
without any change after 8 seconds)
To go back to the functions without any change
press the MENU button again.
Show 1 mode- Fixture is placed on the
floor. Tilt movement angle 210°.
Show 2 mode-Fixture is fixed under
ceiling. Tilt movement angle 90°.
Show 3 mode - Fixture is placed on a
podium, in front of the audience
The spot is always projecting to the
audience's direction; i.e. in front of the
stage. Pan movement angle (left to
right to left): 160°. Tilt movement angle: 90° (60° above horizon; 30° below horizon.)
Show 4 mode - Fixture is fixed under ceiling.
The spot is mainly projecting in front of the stage. Pan movement angle (left to right to left):160°. Tilt
movement angle: 90° (vertically, front 75°; back 15°)
Slave Mode
Used to make the slave unit work in opposite to the master or to work in complete sync.
Press the MENU button until
is shown on the display.
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
(normal) or
BRITEQ
®
OPERATION MANUAL
(2 light show) mode.
5/69
ENGLISH
Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
The unit works to rhythm of the beat when used in standalone or master/slave mode
Press the MENU button until
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
Once the mode has been selected, press the ENTER button save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-
signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone
mode.
Press the MENU button until
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Normal: Panning movement is not inversed.
Pan inversion: Panning movement is inversed
Press the MENU button until
Press the ENTER button, the display starts blinking.
Use DOWN and UP button to select
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Normal: Tilt movement is not inversed.
Tilt inversion: tilt movement is inversed
Press the MENU button until
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Display on: display is always on.
Display off: display is off when not used.
Press the MENU button until the display shows
Press the ENTER button, the display starts blinking.
Use DOWN and UP buttons to select
Once the mode has been selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
BT-36 II
BRITEQ
Sound Mode
is shown on the display.
or
mode.
Blackout Mode
is shown on the display.
(yes blackout) or
Pan Inversion
is shown on the display.
(normal) or
Tilt Inversion
is shown on the display.
(normal) or
Led Display
.
(display always on) or
6/69
®
OPERATION MANUAL
(no blackout) mode.
(pan inversion) mode.
(tilt inversion) mode.
(display off when not used).
BT-36 II
Publicité
