English - AEG MH5G Notice Originale

TECHNICAL DATA
Chipping Hammer
Production code
Rated input
Output
Rate of percussion under load max.
Impact energy per stroke according to EPTA-Procedure 05/2009
Chuck neck diameter
Weight according EPTA-Procedure 01/2003
Noise information
Measured values determined according to EN 60745. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
Measured sound power level
Measured values determined according to 2000/14/EC at the user's ear.
2000/14/EC: Conformity assessment procedure according to Annex VI.
Notified Body: SLG Prüf- und Zertifizierungs GmbH
Burgstädter Straße 20, 09232 Hartmannsdorf, Germany
Measured sound power level
Guaranteed sound power level
Wear ear protectors!
Vibration information
Vibration total values (triaxial vector sum) determined according to EN 60745
Chiselling: Vibration emission value a
Uncertainty K=
WARNING!
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745
and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications,
with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is
running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories,
keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instruc-
tions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
HAMMER SAFETY WARNINGS
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personal injury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring or its own cord. Cutting accessory
contacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
Additional Safety and Working Instructions
Use protective equipment. Always wear safety glasses when working
with the machine. The use of protective clothing is recommended,
such as dust mask, protective gloves, sturdy non-slip footwear,
helmet and ear defenders.
h, Cheq
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a
suitable dust protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g.
asbestos).
When working in walls ceiling, or floor, take care to avoid electric
cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpi-
eces can cause severe injury and damage.
Keep mains lead clear from working range of the machine. Always
lead the cable away behind you.
Switch the device off immediately if the insertion tool stalls! Do
not switch the device on again while the insertion tool is stalled,
as doing so could trigger a sudden recoil with a high reactive force.
Determine why the insertion tool stalled and rectify this, paying
heed to the safety instructions.
Possible causes can be:
• it is tilted in the workpiece to be machined
• breakage of the material to be used
MH 5 G
4431 71 03...
... 000001-999999
1100 W
550 W
3000 min
-1
7,5 J
66 mm
6,0 kg
90,0 dB (A)
101,0 dB (A)
98,6 dB (A)
101 dB (A)
16,7 m/s
2
1,5 m/s
2

English

5
GB