Decommissioning; Switching Off The Appliance; Taking The Appliance Out Of Service; Disposing Of The Appliance - Atag KD80140CDN Mode D'emploi

Decommissioning

A bubbling and gurgling noise.
This noise comes from the refrigerant flowing in the refriger-
→
ation circuit.
The sound is normal.
u
A quiet clicking noise.
The noise is produced whenever the refrigeration unit
→
(motor) automatically switches on or off.
The sound is normal.
u
A hum. It is briefly a little louder when the refrigeration
unit (the motor) switches on.
→ The refrigeration increases automatically when Fast-Freeze
is activated, fresh food has just been placed in the appli-
ance or the door has been left open for a while.
The sound is normal.
u
The ambient temperature is too high.
→
Solution: (see 1.2)
u
A low hum.
→ The sound is produced by air flow noise of the fan.
The sound is normal.
u
Vibratory noise.
→ The appliance is not fixed to the ground. The running of the
cooling unit therefore makes objects and adjacent furniture
vibrate.
u Check installation and reposition appliance as required.
u Move bottles and containers apart.
Flow sound at the soft stop mechanism.
→ The noise is produced when the door is opened and
closed.
The sound is normal.
u
The temperature display indicates:
→ There is a fault.
Please contact the after-sales service (see Maintenance).
u
Power failure flashes in the temperature display
highest temperature reached during power failure is indi-
cated in the temperature display.
→ The freezer temperature rose too high over the last hours or
days due to a power failure or power interruption. When the
power interruption is over, the appliance will continue to
operate in the last temperature setting.
u To cancel the display of the warmest temperature: press
Fig. 2 (6) .
alarm button
u Check the quality of the food. Do not consume spoiled food.
Do not re-freeze thawed food.
DEMO shines in the temperature display.
→ The demo mode is activated.
Please contact the after-sales service (see Maintenance).
u
The outer surfaces of the appliance are warm*.
→ The heat of the refrigeration circuit is used to prevent
condensate from forming.
This is normal.
u
The temperature is not cold enough.
→ The door of the appliance is not properly closed.
Close the door of the appliance.
u
→ Insufficient ventilation.
Keep ventilation grille clear, and clean it.
u
→ The ambient temperature is too high.
Solution: (see 1.2) .
u
→ The appliance was opened too frequently or for too long.
Wait to see whether the appliance reaches the required
u
temperature by itself. If not, please contact the after sales
service (see Maintenance).
→ Too much fresh food
Fast-Freeze.
Solution: (see 5.8)
u
→ The temperature is incorrectly set.
24
to
F0 F9
. The
was placed inside without
Set the temperature to a colder setting and check after 24
u
hours.
The appliance is too close to a source of heat (stove, heater
→
etc).
Change the position of the appliance or the source of heat.
u
→ The appliance was not inserted properly into the recess.
Check whether the appliance was inserted correctly and
u
the door closes properly.
8 Decommissioning

8.1 Switching off the appliance

u Press the On/Off button
Release button.
w If the appliance cannot be switched off, the child lock func-
tion is active (see 5.1) .

8.2 Taking the appliance out of service

u Empty the appliance.
u Switch off the appliance (see Decommissioning).
u Remove mains connector.
u Clean the appliance (see 6.2) .
u Leave the door open to prevent odour.

9 Disposing of the appliance

The appliance contains some reusable materials
and should be disposed of properly - not simply
with unsorted household refuse. Appliances which
are no longer needed must be disposed of in a
professional and appropriate way, in accordance
with the current local regulations and laws.
When disposing of the appliance, ensure that the refrigeration
circuit is not damaged to prevent uncontrolled escape of the
refrigerant it contains (data on type plate) and oil.
u Disable the appliance.
u Pull out the plug.
u Cut through the connecting cable.
* Depending on model and options
Fig. 2 (1) until the display goes dark.