glass 1989 Naked Notice D'installation page 8

InTROdUCTIOn
This manual is designed to be used by installers. It describes
the systems and methods to be adopted for a correct installation
of the product.
The product is not dangerous for the end user if installed, used
and maintained in accordance with the instructions provided
by the manufacturer and on condition that the electrical and
mechanical parts are kept in perfect working order.
For this reason the instructions provided in this manual must be
meticulously followed.
The supporting structure is highly resistant.
SYMBOLS USed
In THIS ManUaL
symbols described below are used in this installation manual
and on certain parts of the product itself.
COnVenTIOnaL SYMBOLS and THeIR MeanInG.
WaRnInG:
GeneRaL danGeR.
Warn user that, if the described operation is not performed
observing safety regulations, there is a risk of physical injury.
nOTe.
Inform the personnel involved - information that, if not observed,
may lead to minor injuries to people or damage to the product.
WaRnInGS.
Inform the personnel involved -important information.
HYdRaULIC InSTaLLeR.
A skilled technician capable to install the product under normal
conditions and carry out all adjustments, maintenance and
repair jobs on mechanical parts as necessary. The technician is
not authorised to work on live electrical systems.
WaRnInG
Inform features present only in some versions of the products.
OPTIOnaL
Items present only if ordered.
COnSUMPTIOn MaTeRIaL
Items not provided by the manufacturer.
SaFeTY ReGULaTIOnS
• Before installing the product, check that the floor where it
will be installed is sufficiently levelled, that it can support its
weight (see installation preparations) and that all necessary
inlets and outlets have been provided.
You must also make sure that the walls and/or floor, on which
the product will be placed up against/installed, are fully tiled
for the entire extension of the product.
• Product maintenance and setup must be performed
exclusively by specialised service personnel only.
ENGLISH
• Remember that all inspection and protective panels must be
refitted after maintenance or adjustment.
• Due to its weight and size, the appliance must be assembled
installed by more than one person.
• Do not tamper,disable or disconnect the product devices.
• In any case, do not create by-passes or use them for purposes
other than those for which they were installed.
• Do not remove or tamper with the inspection panels and do
not remove or conceal the product identification labels.
• Installation of electrical devices (sockets, switches, lamps,
etc.) inside the bathroom where the appliance is to be installed
must be in compliance with current regulations.
• It is absolutely forbidden to use any type of electrical appliance
inside or next to the product during use.
WaRnInG.
do not use acetic silicone.
• Read the instructions supplied with the bottle to make sure
that the silicone is not acetic.
• If acetic silicone is used, acrylic parts might be damaged.
• If you need to replace any parts, contact your nearest service
centre and use original spare parts only.
• At the end of the product's life, do not abandon it in the
environment; contact a disposal firm.
WaRnInG.
The manufacturer declines all responsibility:
• If the installation and maintenance instructions contained
herein are not complied with.
• If the product is not used or installed in compliance with the
existing standards of the installed country.
• If the special maintenance is not carried out by qualified
personnel.
Serial number (Figure A) to state in each intervention request.
do not remove the sticker from the product!
Figure a
WaRnInG.
• Read the manual carefully in all its parts before using the
product.
• Keep this manual for further consultation.
• The manual is intended for different models and versions, so
the product may look different from the manual illustrations.
However the instructions remain unchanged.
• The company reserves the right to make any changes
considered suitable without notice or replacement.
• This product is intended only for the use for which it has been
designed. The manufacturer is not responsible for any damage
caused by improper usage.
• Make sure that the drain is always efficient.
• Ensure that the floor around the product is always dry and
clean, to avoid slips or falls entering or editing the product
itself.
• Pay maximum attention when the surrounding floor is wet,
as there will be a potentially high risk of slipping. this, mainly,
when using soaps, shampoos, clearing detergents, etc..
• It is not advisable to use the shower cabin with water that is too
8