Sulky DPX 24 Notice Originale page 7

Safety regulations
●
●
Every time the tractor/machine assembly is to be
started up and used, you should ensure
beforehand that it complies with current legislation
on safety at work and Road Traffic regulations.
In addition to the instructions contained in this
manual, legislation relating to safety instructions
and accident prevention should be complied with.
Warnings affixed to the machine give
indications regarding safety measures to be
observed and help to avoid accidents.
When travelling on public roads, abide by the
provisions of the Highway Code.
Before starting work, it is essential that the
user familiarizes himself with the control and
operating elements of the machine and their
respective functions. When the machine is
running, it may be too late.
The user should avoid wearing loose clothing
which may be caught up in the moving parts.
We recommend using a tractor with a safety
cab or roll bar conforming to standards in force.
Before starting up the machine and beginning
work, check the immediate surroundings,
particularly for children. Make sure that visibility is
adequate. Clear any persons or animals out of the
danger zone.
It is strictly forbidden to transport any persons
or animals on board the machine whether it is in
operation or not.
The machine should only be coupled up to the
tractor at the specially provided towing points and
in accordance with applicable safety standards.
Extreme care must be taken when coupling
or uncoupling the machine from the tractor.
Before hitching up the machine, ensure that
the front axle of the tractor is sufficiently
weighted. Ballast weights should be fitted to the
special supports in accordance with the
instructions of the tractor manufacturer.
Do not exceed the maximum axle weight or
the gross vehicle weight rating.
Do not exceed the maximum authorized
dimensions for using public roads.
Before entering a public road, ensure that the
protective and signalling devices (lights, reflectors,
etc.) required by law are fitted and working
properly. Replace burnt out bulbs with the same
types and colours.
All remote controls (cords, cables, rods,
hoses, etc.) must be positioned so that they
cannot accidentally set off any manoeuvre which
may cause an accident or damage.
Before entering a public road, place the
machine in the transport position, in accordance
with the manufacturer's instructions.
. Never leave the driver's position whilst the
tractor is running.
The speed and the method of operation must
always be adapted to the land, roads and paths.
Avoid sudden changes of direction under all
circumstances.
Precision of the steering, tractor adhesion,
road holding and effectiveness of the braking
mechanism are influenced by factors such as the
weight and nature of the machine being towed,
the front axle stage and the state of the land or
path. It is essential, therefore, that the appropriate
care is taken for each situation.
Take extra care when cornering, taking
account of the overhang, length, height and
weight of the machine or trailer being towed.
Before using the machine, ensure that all
protective devices are fitted and in good condition.
Damaged protectors should be replaced
immediately.
Before using the machine, check that nuts
and screws are tight, particularly those for
attaching tools (discs, flickers, deflectors, etc.).
Tighten if necessary.
Do not stand in the operating area of the
machine.
Caution! Be aware of any crushing and
shearing zones on remote-controlled and
particularly hydraulically-controlled parts.
Before climbing down from the tractor, or
before any operation on the machine, turn off the
engine, remove the key from the ignition and wait
until all moving parts have come to a standstill.
Do not stand between the tractor and the
machine until the handbrake has been applied
and/or the wheels have been wedged.
. Before any operation on the machine, ensure
that it
cannot be started up accidentally.
Do not use the lifting ring to lift the machine
when it is loaded.
The Spreader must only be used for tasks for
which it has been designed.
The manufacturer will not be liable for any damage
caused by using the machine for applications
other than those specified by the manufacturer.
Using the machine for purposes other than those
originally intended will be done so entirely at the
user's risk.
Proper use of the machine also implies:
- complying with instructions on use, care and
maintenance provided by the manufacturer;
- using only original or manufacturer
recommended spare parts, equipment and
accessories.
The Spreader must only be operated, maintained
and repaired by competent persons, familiar with
the specifications and methods of operation of the
machine. These persons must also be informed of
the dangers to which they may be exposed.
The user must strictly abide by current legislation
regarding:
- accident prevention;
- safety at work (Health and Safety Regulations);
- transport on public roads (Road Traffic
Regulations).
Strict compliance with warnings affixed to the
machine is obligatory.
The owner of the equipment shall become liable
for any damage resulting from alterations made to
the machine by the user or any other person,
without the prior written consent of the
manufacturer.
- The noise emission value measured at the driving
position with the cab closed (level of acoustic
pressure) is 74 dB(A).
Measuring device: SL 401
Position of the microphone placed in accordance
with Paragraph B 2.6 of Appendix B of NF EN ISO
4254-1.
This level of acoustic pressure essentially depends
on the tractor used.
When hitching or unhitching the machine from
the tractor, place the control lever of the hydraulic
lift in such a position that the lifting mechanism
cannot be activated accidentally.
When hitching the machine to the three-point
lifting mechanism of the tractor, ensure that the
diameters of the pins or gudgeons correspond to
the diameter of the tractor ball joints.
Caution! In the three-point lifting zone, there
may be a danger of crushing and shearing.
Do not stand between the tractor and the
machine whilst operating the external lift control
lever.
When in transport, lifting mechanism stabilizer
bars must be fitted to the machine to avoid
floating and side movement.
When transporting the machine in the raised
position, lock the lift control lever.
Never unhitch the machine when the hopper is
full.
(Power take-off and universal drive shafts)
Only use universal drive shafts supplied with
GB