Asist AE5PK110 Mode D'emploi page 39

If the saw blade jams, switch off the appliance imme-
diately.
Do not turn the saw blade while cutting.
WARNING!
Do not remove the workpiece until the saw has
stopped.
CLEANING AND MAINTENANCE
Pull out the appliance before working on it
always the mains plug from the socket.
Store the device and saw blades in a dry and dust-
-free place. The device must always be clean and
free of oil and grease. Use a dry cloth to clean the
surface. Have the carbon brushes replaced only by
the relevant service center or an authorized specialist
workshop.
The ventilation openings must always be free. Remo-
ve adhering dust sawdust with a brush.
Long-term storage decommissioning
Do not store the grinder in a place where the tempe-
rature is high.
If possible, store the machine in a place with a con-
stant temperature and humidity.
SPECIFICATIONS
Voltage 230 V, 50 Hz
(alternating current)
Power consumption 1100 W
Cutting width at 90 ° 127 mm x 127 mm
(without sawing board)
Cutting width at 45 ° 127 mm x 40 mm
(without sawing board)
Idle speed 0–290 min-1
Saw blade speed 0–2.4 m / s
Sections with an inclination of 0 ° - 45 °
Protection class II / (double insulation)
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 90,7 dB (A) KpA=3
LWA (sound power) 101,7 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745:
6,94 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer's instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVIrONmENTAL PrOTECTIONWASTE mA-
NAgEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
electronic equipment (WEEE) and its approximation
in national laws, unfit power tools must be handed
over at the point of purchase of similar equipment, or
in available collection points designated for collection
and disposal of power tools. Such disposed power
tools will be collected, disassembled and delivered for
environment-friendly recycling.
WArrANTY
In the attached material, you will find our warranty
conditions.
Date of manufacture
The date of manufacture is incorporated into the serial
number stated in the product nameplate.
The serial number has the format of ORD-YY- -SERI,
where ORD is the number of purchase order, YY
stands for the year of manufacture,
of manufacture and SERI means the serial product
number.
39
is the month