Topcom BABYVIEWER KS-4246 Manuel D'utilisateur page 6

®
10.11 Playing a lullaby
There are 5 pre-programmed lullabies that you can play on the
baby unit.
– To play the currently selected lullaby or stop playback,
press the music button
– To select a different lullaby, repeatedly press the up
button until the desired lullaby is selected. The
16
lullaby icon will display the selected lullaby (1 to 5).
– Press the on/off button
is selected.
10.12 Switching the night light on and off
– Press the menu button
icon is displayed.
– Press the up
16
the night light "ON" (night light
– Press the menu button
– After 10 seconds the parent unit will switch back to
monitor mode.
10.13 Voice activated transmission (VOX)
During night and to save energy, the KS-4246 can be set in VOX
mode.
In VOX mode, the display will be activated as soon as the
microphone of the baby unit will capture sound.
You can set the sound detection sensitivity (VOX) of the
babyphone. If the sensitivity is set to high, the baby unit will pick
up weaker sounds.
– Press button
23
– Repeatedly press button
VOX sensitivity.
The VOX sensitivity is indicated by a black bar on
the display:
- high sensitivity
- low sensitivity
– To switch off VOX mode, select "OFF".
– Press the menu button
10.14 Night vision
The camera has 6 high-intensity LED's for picking up clear images
in the dark. When the build in light sensor
ambient light level as low, the LED's will automatically activate.
The image changes automatically into black and
white mode under the night vision mode.
10.15 Registering the parent unit with the baby unit
or register a new camera.
Up to 4 baby units can be registered to one parent unit.
To re-register your baby unit, or register a new baby unit, follow
the procedure below:
– Switch on the parent unit
– On monitor mode, press and hold camera button
for 5 seconds, it will go to registration mode.
– After registration icon
or down button
16
channel [C1] or [C2] or [C3] or [C4] that you want the
baby unit to pair with.
– Press and release the menu button
which camera number to be registered.
– The Link LED then flashes rapidly for 10 seconds.
21
– Switch the baby unit ON. Press the pair button
(at the back of the camera).
– If registration is completed, camera video appears on
LCD screen and return to normal mode. Baby unit will
return to normal mode too.
– If the registration time is expired or registration is failed,
"Out of Range" appears on LCD.
NOTE: If a particular channel had been registered already,
register this particular channel again will over-write the old
registration.
6
on the baby unit.
18
when the desired lullaby
25
5 times. The night light
23
or down button to switch
17
is on) or "OFF".
2
to confirm.
23
6 times. "VOX" is displayed.
or to set the
16 17
to confirm.
23
measures the
9
comes out, pthe up button
to select the camera
17
to confirm
23
10
10.16 Selecting the camera
When more than 1 camera is registered.
On monitor mode:
– Press the camera button
number is displayed.
– Press the camera button
camera or select 'SCAN'. In scan mode, each camera
image will be displayed sequentially.
If only one camera registered, a short press on the camera button
will have no response!
19
11 Cleaning and maintenance
This section contains important instructions for cleaning and
maintaining the equipment.
Follow these instructions to ensure trouble-free use and prevent
damage to the equipment due to improper maintenance.
11.1 Safety Instructions
DANGER
Risk of fatal injury due to electric shock!
• Before cleaning the equipment, switch it off and
unplug the power cable from the mains receptacle.
CAUTION
Risk due to leaking battery fluid
Fluid from leaking batteries (regular or rechargeable) can
cause injuries (skin irritation) or damage to the equipment.
Wear safety gloves.
CAUTION
• Do not use cleaning products or solvents. They can
damage the case or seep into the equipment and
cause permanent damage.
11.2 Cleaning
– Clean the equipment with a soft, slightly dampened
cloth.
– Clean soiled connectors and contacts with a soft brush.
– Clean the battery contacts and battery compartment with
a dry, lint-free cloth.
– If the equipment gets wet, switch it off and remove the
batteries immediately. Wipe the battery compartment dry
with a soft cloth in order to minimize potential water
damage. Leave the battery compartment open until it is
completely dry. Do not use the equipment before it is
completely dry.
11.3 Maintenance
– Check the batteries (regular or rechargeable) in the
equipment regularly and replace them when necessary.
– Check the connectors and cables for defects.
CAUTION
19
• If you suspect that the equipment is damaged, always
have it checked by an expert before using it again.
12 Troubleshooting
This section provides important instructions for localising and
correcting problems.
Follow these instructions in order to avoid hazards and damage.
12.1 Safety Instructions
once
DANGER
Risk of fatal injury due to electric shock!
• Unplug the power cable before attempting to correct a
problem.
Babytalker 3500 SEDS
briefly. The camera
19
again to select another
19