Publicité
Les langues disponibles
Les langues disponibles
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
Installing and Removing Blades
CAUTION: Cut Hazard. Blade tension lever is under
spring pressure. Maintain control of lever when
releasing blade tension.
WARNING: ALWAYS wear gloves when touching the
saw blade.
To Install Blade (Fig. A, D–F)
1. Rotate the blade tension lever
until it stops to release tension on blade (refer to
Figure A).
2. Turn the saw over and place it on a workbench or table.
3. Unlatch the two blade guard latches
blade guard.
4. Position the blade so that the teeth face out from the
saw and cut towards the work stop
blade direction
5. Slip blade into the guide rollers
pulleys
16
as shown in Figure D.
6. Make sure that the blade is fully inserted into the guide
rollers and positioned fully on the rubber tires
just touching the rear guide bearings
7. Rotate the blade tension lever
it stops and then close blade guard and secure latches.
Make sure the teeth face away from the band saw
(Fig. A, D).
8. Turn the saw on and off a few times to ensure that the
blade is seated properly.
To Remove Blade (Fig. A, D–F)
1. Rotate the blade tension lever
until it stops to release tension in blade (refer to
Figure A).
2. Turn the saw over and place it on a workbench or table.
3. Unlatch the two blade guard latches and open the
blade guard.
4. When removing the blade, tension may be released and
the blade may spring free. SAW BLADES ARE SHARP. USE
CARE IN HANDLING THEM.
clockwise 180 degrees
7
and open the
11
5
.
5
17
and around both
and
19
.
18
7
counterclockwise until
7
clockwise 180 degrees
5. Inspect the guide rollers
which may be lodged in them. Lodged chips can prevent
rotation of the guide rollers and cause flat spots on the
guide rollers.
6. Rubber tires
are mounted on the pulleys
19
rubber tires should be inspected for looseness or damage
when changing the blade. Wipe any chips from the
rubber tires on the pulleys with a brush.
nOTE: Do not use your hands to wipe chips.
This will extend tire life and keep the blade from slipping.
If any looseness or damage occurs, the tool should be
brought to an authorized D
repair or replacement as soon as possible. Continued use
of the tool with loose or damaged rubber tires will cause
unstable travel of the band saw blade.
7. Close the blade guard and securely latch the two
blade guard latches. Rotate the blade tension lever
counterclockwise 180 degrees until it stops.
Blade Tracking (Fig. A, E, G)
WARNING: To reduce the risk of serious personal
injury, turn tool off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start‑up can cause injury.
NOTICE: Excessive tightening of the adjustment screws
could result in damage to the saw.
Your band saw is equipped with an adjustable blade tracking
mechanism which assures proper blade tracking at all times.
The blade is properly adjusted when it is sitting fully on
rubber tires
19
and lightly touching one or both of the rear
guide bearings
18
.
To Adjust the Blade Tracking
1. Turn and open the blade tension lever
to the tracking screw
2. Use a 10 mm wrench to loosen the locking nut
(Fig. G).
3. Use a 3 mm hex wrench
1/4 turn clockwise or counterclockwise (Fig. G).
nOTE: Turning the tracking screw clockwise moves
the blade toward the guide roller, turning the tracking
screw counterclockwise moves the blade away from the
guide roller.
4. Tighten the locking nut and close the blade tension lever
and blade guard. (It will be necessary to run the saw to
observe the tracking.)
5. Observe blade tracking between runs and repeat Steps
1–4 as necessary to achieve proper blade tracking.
Blades
This portable band saw is setup for use with .02"
(0.5 mm) thick, 1/2" (12.7 mm) wide and 27" – 27-1/4"
(686 mm–692 mm) long blades. DO nOT use .025"
(0.64 mm) thick blades.
WARNING: The use of any other blade or accessory
might be hazardous. DO NOT use any other type
of accessory with your band saw. Blades used on
17
and remove any large chips
16
WALT service center for
e
to allow access
7
.
12
to turn the tracking screw
4
English
. The
7
6
12
9
Publicité
