Titan IMPACT 740 Notice D'utilisation page 3

Important Safety Information
haZaRD: EXPLOSION haZaRD DuE TO
INcOMPaTIBLE MaTERIaLS
Will cause property damage or severe injury.
PREvENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such
as bleach, mildewcide, methylene chloride and 1,1,1 -
trichloroethane. They are not compatible with aluminum.
• Contact your coating supplier about the compatibility of
material with aluminum.
haZaRD: GENERaL
Can cause severe injury or property damage.
PREvENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• The United States Government Safety Standards have
been adopted under the Occupational Safety and Health
Act (OSHA). These standards, particularly part 1910 of
the General Standards and part 1926 of the Construction
Standards should be consulted.
• Use only manufacturer authorized parts. User assumes
all risks and liabilities when using parts that do not meet
the minimum specifications and safety requirements of the
pump manufacturer.
• All hoses, fittings, and filter parts must be secured before
operating spray pump. Unsecured parts can eject at great
force or leak a high pressure fluid stream causing severe
injury.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it with
another grounded high-pressure hose.
• Do not kink or over-bend the hose. Airless hose can
develop leaks from wear, kinking and abuse. A leak can
inject material into the skin.
• Do not expose the hose to temperatures or pressures in
excess of those specified by manufacturer.
• Do not spray outdoors on windy days.
• Wear clothing to keep paint off skin and hair.
• Do not operate or spray near children. Keep children
away from the equipment at all times.
• Do not overreach or stand on an unstable support. Keep
effective footing and balance at all times.
• Use lowest possible pressure to flush equipment.
• Stay alert and watch what you are doing.
• Do not operate the unit when fatigued or under the
influence of drugs or alcohol.
• For electric units — Always unplug cord from outlet before
working on equipment.
• Do not use the hose as a strength member to pull or lift the
equipment.
• Do not lift by cart handle when loading or unloading.
© Titan Tool Inc. All rights reserved.
operating the equipment. SavE ThESE INSTRucTIONS.
·
Read all safety information before
Grounding Instructions
This product must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This product is
equipped with a cord having a grounding wire with an appropriate
grounding plug. The plug must be plugged into an outlet that
is properly installed and grounded in accordance with all local
codes and ordinances.
WaRNING - Improper installation of the grounding plug can
result in a risk of electric shock.
If repair or replacement of the cord or plug is
necessary, do not connect the green grounding wire
to either flat blade terminal. The wire with insulation
having a green outer surface with or without yellow
stripes is the grounding wire and must be connected
to the grounding pin.
Check with a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if you are in doubt
as to whether the product is properly grounded. Do not modify
the plug provided. If the plug will not fit the outlet, have the
proper outlet installed by a qualified electrician.
Grounded Outlet
Grounding Pin
Cover for grounded outlet box
IMPORTaNT: use only a 3-wire extension cord that has
a 3-blade grounding plug and a 3-slot receptacle that will
accept the plug on the product. Make sure your extension
cord is in good condition. When using an extension cord,
be sure to use one heavy enough to carry the current your
product will draw. an undersized cord will cause a drop in
line voltage resulting in loss of power and overheating. a 12
gauge cord is recommended. If an extension cord is to be
used outdoors, it must be marked with the suffix W-a after
the cord type designation. For example, a designation of
SjTW-a would indicate that the cord would be appropriate
for outdoor use.
IMPORTaNT: When the sprayer is used with a generator
or uncontrolled line voltage, the use of Titan's "Line Surge
Protector" (P/N 800-935) is recommended.
Specifications
Gallons per minute (GPM)
740..............................................0.80 (3.0 LPM)
840..............................................0.95 (3.6 LPM)
Maximum tip sizes
740..............................................0.029"
840..............................................0.031"
Maximum pressure ..........................3300 PSI (22.8 MPa)
Voltage ............................................100~120V AC, 50/60 Hz
Power
740..............................................1.8 HP Brushless DC Motor
840..............................................2.1 HP Brushless DC Motor
Maximum current consumption .......15 A
Weight, high rider ............................95 lbs. (43.1 kg)
Weight, low rider ..............................81 lbs. (36.7 kg)
Maximum hose length .....................300' (91.4 m)
Generator requirement ....................5000 Watt (disable idle-down
3
feature)
English