Assembly; Start-Up - ATIKA KLS 1600 Notice Originale

− leaving unattended (even during short interruptions)
unusual noises and vibrations
−
Thoroughly maintain your garden vac:
− Ensure that all nuts, bolts and screws are tight.
− Make sure that the ventilation apertures are free.
− Keep handles dry and free of oils and grease.
Check the machine for possible damage
Before continuing to use the machine, the protective
−
devices must be inspected to ensure that they work
perfectly and with their intended function
Check whether movable parts function perfectly and do
−
not stick or whether parts are damaged. All parts must be
correctly installed and fulfil all conditions to ensure perfect
operation of the saw
Damaged guards and parts must be properly repaired or
−
exchanged by a recognized, specialist workshop; insofar
as nothing else is stated in the instructions for use.
Damaged or illegible safety warning labels should be
−
replaced immediately.
Store the unused machine in a dry locked place away from the
reach of children.
Electrical safety
Design of the connection cable according to IEC 60245 (H 07
RN-F) with a core cross-profile section of at least
→ 1.5 mm² for cable lengths up to 25 m
→ 2.5 mm for cable lengths over 25 m
2
Long and thin connection lines result in a potential drop. The
motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs and coupler outlets on connection cables must be made
of rubber, non-rigid PVC or other thermoplastic material of
same mechanical stability or be covered with this material.
The connector of the connection cable must be splash-proof.
When running the connection line observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Do not drive the device across the extension cable. Make sure
that it is behind you in a secure position. Place the cable on a
path or area that has already been thatched.
Wind off completely the cable when using a cable drum.
Do not use the cable for purposes for which it is not meant.
Protect the cable against heat, oil and sharp edges.
Do not use the cable for machine carrying and hanging up or
for pulling the plug out of the socket.
Protect yourself against electric shocks. Avoid touching
earthed parts with your body (e.g. pipes, heating apparatus,
cookers, fridges etc.).
Do never connect a damaged cable to the mains. Do not
touch a damaged cable before it is disconnected from the
mains. A damaged cable may cause contact with live parts.
Do not use any defective connection cables.
When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
Do not set up any provisional electrical connections.
Never bypass protective devices or deactivate them.
Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of the
machine must be carried out by a certified electrician or one
of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Damaged mains leads must be replaced by the
manufacturer or one of their service workshops or a similar
qualified person to prevent dangers.
Repairs to other parts of the machine must be carried out by
the manufacturer or one of his customer service points.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.

Assembly

Connect the leaf sucker to the power supply system only
after having finished the complete assembly.
Mount the operating bar (9).
Mount the handle (1).
Fix the cable on the operating bar (9) using the cable
clip (4).
Slip the collecting bag (10) on.
Turn the handle of the collecting bag clockwisely to
secure the collecting bag.
Hang up the collecting bag.
Plug the connector of the blow hose (7) in the suction
funnel (17)
Hang up the blow hose (7).
Put the extension blow tubes (11) in their receivers on
the machine to properly keep them.

Start-up

Check that the machine is completely and correctly
assembled.
Before using the shredder, make sure each time that
there are no faulty connections (tears, cuts, etc.)
−
there are no damage at the machine
−
all screws are tight
−
the collecting bag shows no signs of wearing or quality
−
deterioration
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Only use connection cables with sufficient diameters.
Do not use any defective connection cables.
Connect the machine via a 30 mA fault current safety switch.
Use connecting or extension cables up to a length of 1.5 m
featuring a core cross section of at least 25 mm²
Fuse protection: 10 A
Mounting of the extension cable
1. Plug the female connector of the extension cable on the male
connector of the device.
2. Thread the extension cable through the pull relief device (3)
as a loop and hang it up.
3. Make sure that the extension cable has enough free motion.
13