Publicité
Les langues disponibles
Les langues disponibles
ENGLISH
1) INSTALLATION INSTRUCTIONS
2) Electronic valve
3) PRECAUTIONS FOR USE (The product guarantee depends on the respect for these rules)
INSTALLATION and START UP
For products delivered with filters, these must be installed in accordance with the instructions.
Before commissioning any of our valves, it is essential to carefully drain
the pipes which can damage the mechanisms or water passages (PRESTO® heads that can be dismantled from front).
Recommended operating pressure according to NF EN 816: 1 to 5 bars.
CLEANING
The chrome-plated coating of PRESTO® valves must be cleaned only with soapy water.
Abrasive, acid, alkaline or ammonia-based household products are prohibited.
4) Rotating mixing valve
5) Fixed model
6) Part no. 55132 - Battery
Part no. 55137 - Mains
Part no. 55130 - Battery
Part no. 55135 - Mains
7) Part no. 55133 - Battery
Part no. 55138 - Mains
Part no. 55131 - Battery
Part no. 55136 - Mains
8)
Part no.
Rotating
Fixed
mixing
mixing
valve
valve
55132
x
55137
x
55133
55138
55130
x
55135
x
55131
55136
9) Commissioning
For proper operation of the sensor tapware, avoid installing these products facing a mirror or any other reflective surfaces. Do not
install 2 sensor taps facing one another.
10) Wall rosette part no. 40020
11) 230VAC / 7VDC power supply by cable 2x0.5 mm² min. Ø6 to 8.5 mm duct
Disconnect the power supply before any intervention on the valve.
The transformer is equipped with an overload thermal protection.
When it is operating, it is necessary to switch off the electrical supply for 30 seconds to
reset it, after having eliminated the cause of the fault.
12) Attachment: 2 screws Ø 4.5 max
13) Top
14) Bottom
15) Recommended operating pressure: 0.1 Mpa (1 bar) to 0.5Mpa (5 bars).
Limit operating pressure: 0.05 MPa (0.5 bars) to 0.8 MPa (8 bars). Valve protection index IP54.
16) Flow curve
17) Flow rate (l/min)
18) Laminar spout
19) Bar
20) Regular rinsing. A flow of 30 seconds is carried out 72 hours after last use, then every 72 hours, in order to prevent water
stagnation and reduce the risk of legionella.
21) MAINTENANCE
22) Replacing the battery part no. 90941
23) WORN-OUT BATTERY LED flashing constantly Out of order
24) Lithium battery 6V CRP2 Part no. 90941
25) Replacing the solenoid valve part no. 90944
26) Seal replacement!
27) Solenoid valve Part no. 90944
28) Replacing the circuit
29) Circuit part no. 90943
30) This document is not contractual; we reserve the right to modify the characteristics of our products without notice.
31) PATENTED and REGISTERED MODELS
Power
Secured
supply
power
lithium
supply
battery
230V/7V –
CRP2
1.05W
6V DC
IP65
watertight
x
x
x
x
x
x
x
x
x
x
x
x
Regular
Shut-
PEX
rinsing
off
hoses
valves
female
filter
nut
angle
G3/8"
G1/2"-
Lg.
G3/8"+
350mm
rosette
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Non-
Laminar
Self-
return
spout
adhesive
Bushing
8l/min
panel
NF
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
X
X
X
X
X
X
X
X
Publicité
