Triton TPT 125 Instructions D'utilisation Et Consignes De Sécurité page 6

NOTE: The term "residual current device (RCD)" may be replaced by the term
"ground fault circuit interrupter (GFCI)" or "earth leakage circuit breaker
(ELCB)".
WARNING: When used in Australia or New Zealand, it is recommended that
this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.
WARNING: Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the user,
and damage to the tool. If in doubt, do not plug in the tool. Using a power
source with a voltage less than the nameplate rating is harmful to the motor.
Polarized Plugs (for North America only) To reduce the risk of electric shock,
this equipment has a polarized plug (one blade is wider than the other). This
plug will fit in a polarized outlet only one way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug in any way.
General & Electrical Safety (US)
• In the event of a malfunction or breakdown, grounding provides a path of
least resistance for the electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord with an equipment-grounding
conductor and a grounding plug.
• The plug must be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
• Do not modify the plug provided – if it will not fit the outlet, have the proper
outlet installed by a qualified electrician.
• Improper connection of the equipment-grounding conductor can result in a
risk of electric shock. The conductor with green insulation - with or without
yellow stripes - is the equipment-grounding conductor.
• If repair or replacement of the electric cord or plug is necessary, do not
connect the equipment-grounding conductor to a live terminal.
• Check with a qualified electrician or service personnel if the grounding
instructions are not clear, or if in doubt as to whether the tool is properly
grounded.
• Use only 3-wire extension cords with 3-prong grounding plugs and 3-pole
receptacles that accept the tool's plug.
• Repair or replace damaged or worn cord immediately.
This tool is intended for use on a circuit with an outlet that resembles Figure
A. The tool has a grounding plug similar to the plug illustrated. A temporary
adapter, which resembles the adapter illustrated in Fig B, may be used to
connect this plug to a 2-pole receptacle if a properly grounded outlet is not
available. The temporary adapter should be used only until a properly-
grounded outlet can be installed by a qualified electrician. The green-colored
grounding clip with metal screw extending from the adapter, must be
connected to a permanent ground such as a properly-grounded outlet box.
Grounding
Pin
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of checking to
EN
see that keys and adjusting wrenches are removed from the tool before
switching it 'ON'.
3. KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
4. DON'T USE IN DANGEROUS ENVIRONMENTS. Don't use power tools in
damp or wet locations, or expose them to rain. Keep work area well
illuminated.
5. KEEP CHILDREN AWAY. All visitors should be kept a safe distance from
work area.
6
Metal Screw
Curve of grounded
outlet box
(A)
6. MAKE THE WORKSHOP CHILD-PROOF with padlocks, master switches, or
by removing starter keys.
7. DON'T FORCE THE TOOL. It will perform more efficiently and safely when
working at the rate for which it was designed.
8. USE THE CORRECT TOOL. Don't force the tool or attachment to perform a
task for which it was not designed.
9. USE THE CORRECT EXTENSION CORD. Make sure the extension cord is in
good condition. When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An undersized cord will
cause a drop in line voltage, resulting in loss of power and overheating.
The table below shows the correct size to use depending on cord length
and the nameplate ampere rating. If in doubt, use the next heavier gauge.
The smaller the gauge number, the heavier the cord.
Total length of cord in feet
25 feet
50 feet
Not recommend to use the extension cord more than 50 feet
10. WEAR CORRECT APPAREL. Do not wear loose clothing, gloves, neckties,
rings, bracelets, or other jewelry which may get caught in moving parts.
Non-slip footwear is recommended. Wear protective hair covering to
contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use a face or dust mask if the cutting
operation is dusty. Everyday eyeglasses only have impact-resistant lenses;
they are NOT safety glasses.
12. SECURE WORK. Use clamps or a vise to hold work when practical. It is
safer than using hands and also it frees both hands to operate tool.
13. DON'T OVERREACH. Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating and changing
accessories.
15. DISCONNECT TOOLS before servicing, and when changing accessories,
such as blades, bits, cutters etc.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in
'OFF' position before plugging in.
17. USE RECOMMENDED ACCESSORIES. Consult the owner's manual for
recommended accessories. The use of incorrect accessories may create a
risk of injury to persons.
18. NEVER STAND ON TOOL. Serious injury could occur if the tool is tipped or if
the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other
part that is damaged should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.
20. DIRECTION OF FEED. Feed work into a blade or cutter against the direction
of rotation of the blade or cutter only.
21. NEVER LEAVE THE TOOL RUNNING UNATTENDED. SWITCH THE POWER OFF.
Do not leave the tool unattended until it comes to a complete stop.
(B)
Gauge number of the cord
14 AWG
12 AWG