General Safety - Triton TPT 125 Instructions D'utilisation Et Consignes De Sécurité

WARNING: Always wear ear protection where the sound level exceeds 85dB(A)
and limit the time of exposure if necessary. If sound levels are uncomfortable,
even with ear protection, stop using the tool immediately and check the ear
protection is correctly fitted and provides the correct level of sound attenuation
for the level of sound produced by your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch,
numbness, tingling and reduced ability to grip. Long term exposure can lead to
a chronic condition. If necessary, limit the length of time exposed to vibration
and use anti-vibration gloves. Do not operate the tool with hands below a
normal comfortable temperature, as vibration will have a greater effect. Use
the figures provided in the specification relating to vibration to calculate the
duration and frequency of operating the tool.
A poorly maintained, incorrectly assembled, or misused tool, may produce
increased levels of noise and vibration.

General Safety

WARNING! When using electric power tools, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and personal injury
including the following safety information. Read all these instructions before
attempting to operate this product and save these instructions for future use.
WARNING: This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience or
knowledge unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children must be
supervised to ensure that they do not play with the appliance.
CAUTION: Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1 - Keep work area clear - Cluttered areas and benches invite injuries
2 - Consider work area environment
- Do not expose tools to rain
- Do not use tools in damp or wet locations
- Keep work area well lit
- Do not use tools in the presence of flammable liquids or gases
3 - Guard against electric shock - Avoid body contact with earthed or
grounded surfaces (e.g. pipes, radiators, ranges, refrigerators)
4 - Keep other persons away - Do not let persons, especially children, not
involved in the work touch the tool or the extension cord and keep them
away from the work area
5 - Store idle tools - When not in use, tools should be stored in a dry
locked-up place, out of reach of children
6 - Do not force the tool - It will perform the job better and safer at the rate
for which it was intended
7 - Use the right tool - Do not force small tools to do the job of a heavy duty
tool
Do not use tools for purposes not intended; for example do not use circular
saws to cut tree limbs or logs
8 - Dress appropriately
- Do not wear loose clothing or jewellery, which can be caught in moving
parts
- Suitable safety footwear is recommended when working outdoors.
- Wear protective covering to contain long hair
9 - Use protective equipment
-Use safety glasses
-Use face or dust mask if working operations create dust
WARNING: Not using protective equipment or appropriate clothing can cause
personal injury or increase the severity of an injury.
10 - Connect dust extraction equipment - If the tool is provided for the
connection of dust extraction and collecting equipment, ensure these are
connected and properly used
11 - Do not abuse the power cable - Never yank the power cable to
disconnect it from the socket. Keep the power cable away from heat, oil
and sharp edges. Damaged or entangled power cables increase the risk
of electric shock
12 - Secure work - Where possible use clamps or a vice to hold the work. It
is safer than using your hand
13 - Do not overreach - Keep proper footing and balance at all times
14 - Maintain tools with care
- Keep cutting tools sharp and clean makes the tool easier to control
and less likely to bind or lock in the workpiece
- Follow instruction for lubricating and changing accessories
- Inspect tool power cables periodically and if damaged have them
repaired by an authorized service facility
- Inspect extension cables periodically and replace if damaged
- Keep handles dry, clean and free from oil and grease
WARNING: Many accidents are caused by poorly maintained power tools.
15 - Disconnect tools - When not in use, before servicing and when
changing accessories such as blades, bits and cutters, disconnect tools
from the power supply
WARNING: The use of accessories or attachments not recommended by the
manufacturer may result in a risk of injury to persons.
16 - Remove adjusting keys and wrenches - Form the habit of checking to
see that keys and adjusting wrenches are removed from the tool before
switching it 'ON'
17 - Avoid unintentional starting - Ensure switch is in "O' position when
connecting to a mains socket or inserting a battery pack, or when
picking up or carrying the tool
WARNING: Unintended starting of a tool can cause major injuries.
18 - Use outdoor extension leads - When the tool is used outdoors, use
only extension cords intended for outdoor use and so marked. Use of an
extension cable suitable for outdoor use reduces the risk of electric shock
19 - Stay alert
- Watch what you are doing, use common sense and do not operate the
tool when you are tired
- Do not use a power tool while you are under the influence of drugs,
alcohol or medication
WARNING: A moment of inattention while operating power tools may result in
serious personal injury.
20 - Check damaged parts
- Before further use of tool, it should be carefully checked to determine
that it will operate properly and perform its intended function
- Check for alignment of moving parts, binding of moving parts, breakage
of parts, mounting and any other conditions that may affect its
operation
- A guard or other part that is damaged should be properly repaired or
replaced by an authorized service centre unless otherwise indicated in
this instruction manual
- Have defective switches replaced by an authorized service centre
WARNING: Do not use the tool if the ON/OFF switch does not turn it 'ON' and
'OFF'. The switch must be repaired before the tool is used.
21 - Have your tool repaired by a qualified person - This electric tool complies
with the relevant safety rules. Repairs should only be carried out by
qualified persons, otherwise this may result in considerable danger to the
user
WARNING: When servicing use only identical replacement parts.
WARNING: If the power cable is damaged it must be replaced by the
manufacturer or an authorised service centre.
22 - Power tool mains plugs must match the mains socket - Never modify
the plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodified plugs and matching sockets will
reduce risk of electric shock
23 - If operating a power tool outside use a residual current device (RCD) -
Use of an RCD reduces the risk of electric shock
EN
5