D-Link DNETDEFEND DFL-2560 Guide D'installation page 2

About This Guide
This guide contains step-by-step instructions
for setting up the D-Link DFL-2560/DFL-2560G
Firewall. Please note that the model you have
purchased may appear slightly different from
those shown in the illustrations.
Unpacking the Product
Open the shipping carton and carefully unpack
its contents. Please consult the packing list
located in following information to make sure all
items are present and undamaged. If any item
is missing or damaged, please contact your
local D-Link reseller for replacement.
- One (1) DFL-2560(G) NetDefend UTM
Firewall
- One (1) Power Cord
- One (1) Console Cable
- One (1) Ethernet Cable
- One (1) Ethernet Cable
- One (1) Reference CD
(Contains documentation in PDF format)
- Two (2) Rack Mounting Brackets
- One (1) 12-Month IPS Subscription
- One (1) 12-Month Anti-Virus Subscription
Product Overview
Front Panel - DFL-2560 and DFL-2560G
G F
Figure 1. DFL-2560/ 2560G Front Panel
2  D-Link NetDefend Firewall
(RS232)
(CAT5 UTP/Straight-through)
(CAT5 UTP/ Cross Over)
C A
E D B
Item Feature
A LCD Panel
B Keypad
C LEDs
D Console Port
E USB Ports (2)
F 10/100/1000Mbps
Ethernet Ports*
G 10/100/1000Mbps
Ethernet Ports*
(DFL-2560)
1000Mbps
SFP Port*
(DFL-2560G)
Table 1. DFL-2560/ 2560G Front Panel Descriptions
* Configurable Gigabit Ethernet ports with autosensing
duplex and auto MDI/MDIX. When configuring one of the
ports, reference the interface name that corresponds to
the location of the port. For the default interface name
bindings for each Ethernet port, see Table 2 "Default
Interface Assignment".
DFL-2560/ 2560G Default Interface Settings
Interface Interface
Port Name Type
1 DMZ1 Static IP
2 DMZ2 Static IP
3 DMZ3 Static IP
4 DMZ4 Static IP
5 WAN1 DHCP
Client
6 WAN2 Static IP
7 LAN1 Static IP
8 LAN2 Static IP
9 LAN3 Static IP
10 LAN4 Static IP
Table 2. Default Interface Assignment
Note: D-Link NetDefend Firewalls only allow
Web GUI access from the LAN1 port by default
for security reasons. That means the Web GUI
access is only allowed on port No. 7 of front
plate by default for DFL-2560/DFL-2560G.
Description
Used to display status and operation
messages.
These keys are used in conjunction with
the messages on the LCD Panel.
Power LED (top): Indicates that the
NetDefend UTM firewall is powered on.
System LED (bottom): Indicates the
system status of the NetDefend UTM
firewall
Used to access the NetDefendOS
Command Line Interface (CLI) via
RS232 Cable.
Reserved for future use.
The assigned numbers for the ports are
5 to 10 (from left to right).
The assigned numbers for the ports are
1 to 4 (from left to right).
Web-Based
IP Address Mgmt
172.17.100.254/24 Disabled
172.17.110.254/24 Disabled
172.17.120.254/24 Disabled
172.17.130.254/24 Disabled
N/A Disabled
192.168.120.254/24 Disabled
192.168.10.1/24 Enabled
192.168.20.1/24 Disabled
192.168.30.1/24 Disabled
192.168.40.1/24 Disabled