Cardin Elettronica SL Série Mode D'emploi page 19

DISPLAY MODE
Using the PROG button you can access the following functions in sequence:
- memorising the status of the dip-switches;
- display the status of the command and safety devices;
The status of the security devices TB, FTCI, FTCS,
CSP are always shown on the display.
Memorises the DIP-SWITCH settings and displays
the firmware version e.g. ("_11")
The segments regarding the command status (LED
"ON" command active) and safety status (LED
est) light up.
The number of manoeuvres appears on the
display. This number always remains visible
until you change the setting. Once 999999
has been exceeded the lighting up of the
decimal point on the display equals 1 million
+ the six figure number.
PRESS
PROG
Sensitivity
Torque
PRESS
PROG
0
TB N.C. N.C. N.C.
FTCS N.C. N.C. N.C.
FTCI N.C. N.C. 8.2 K 8.2 K
CSP N.C. 8.2 K
PRESS For the values from A to F see paragraph "safety contact selection" on page 22
PROG
Setting the motor position to define the direction:
PRESS
PROG
Limited opening setting in steps of 1 meter:
PRESS
PROG
Value
Limit mm
The setting is actuated both in the opening and in the closing directions
PRESS
PROG
Automatic repositioning setting
PRESS
PROG
Reclosing function after encountering an obstacle
PRESS
PROG
TD mode only in the opening direction (only with DIP1 "ON")
PRESS PROG
PRESS PROG
PRESS PROG
Current sensor/motor torque limit setting*
0 1 2 3 4 5 6 7
max med min max med min max med min min
28 % 35 % 60 %
Safety contact selection
1 2 3 4 5 6 7 8
N.C. N.C. N.C. N.C. N.C. 8.2 K 8.2 K
N.C. 8.2 K 8.2 K 8.2 K 8.2 K N.C. N.C.
N.C. N.C. 8.2 K 8.2 K N.C. N.C.
N.C. 8.2 K N.C. 8.2 K N.C. 8.2 K N.C. 8.2 K
e installed to the left, closing towards the right
e installed to the right, closing towards the left
es
Setting the travel limit distance
0 1 2 3 4 5 6 7 8 9
-6 -12 -18 -24 -30 -36 -42 -48 -54 - 60
epositioning disabled
epositioning enabled
d
- display the number of manoeuvres;
test
- setting the current sensor level/motor torque level;
- selecting the type of safety contact;
- setting the: position of the motor; limited opening in steps of 1 meter; distance
from the travel limit; automatic repositioning, automatic closing attempts; TD
mode only in the opening direction.
In the test
motor has stopped) it is possible to check the
status of the command and safety devices
10 sec
and carry out maintenance interventions.
The warning lights and indicator light will
activate once, each time a
TA-TC-TD-TB-FTCI-FTCS-CSP
is received.
To return to the normal operating mode
press PROG
the indication test
10 sec
8 9
PRESS PROG
Each time the button is pressed the
90%
number will increase (from 0 to 9).
10 sec
9
PRESS PROG
Each time the button is pressed the setting
will change (between 0 ... 9 - A ...F).
10 sec
PRESS PROG
Each time the button is pressed the
setting will change (between 0 and 1).
10 sec
PRESS PROG
Each time the button is pressed the
number will increase (from 1 to 4).
10 sec
PRESS PROG
Each time the button is pressed the
number will increase (from 0 to 9).
10 sec
PRESS PROG
Each time the button is pressed the
setting will change (between 0 and 1).
10 sec
PRESS PROG
Each time the button is pressed the
setting will change (between 1 and 7).
10 sec
PRESS PROG
Each time the button is pressed the
setting will change (between 0 and 1).
10 sec
19
10 sec
ed.
PRESS PROG
When the
TA-TC-TD-TB-FTCI-FTCS-CSP
inputs are activated the warning
lights will light up.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg. 6)
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
10 seconds after the last
modification you will be
automatically moved out of
the mode and the selected
values will be saved (eg.
5)
1)
4)
8)
0)
4)
1)