Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
R
i
s
R
i
s
Even if used properly, residual risks can exist even if the
relevant safety regulations are complied with due to the design
determined by the intended purpose.
Residual risks can be minimised if the "Safety information" and
the "Intended usage" as well as the whole of the operating
instructions are observed.
Observing these instructions, and taking proper care, will
reduce the risk of personal injury or damage to the equipment.
Electrostatic discharge on the extraction hose.
Crushing on moveable machine parts.
Discharge of dusts.
Risk from electricity, by using non-standard electrical
connections.
Touching live parts of opened electrical components.
Impairment of hearing when working on the machine for
longer periods of time without ear protection.
Fire danger.
In addition, in spite of all the precautionary measures taken,
non-obvious residual risks can still exist.
S
a
f
e
t
y
S
a
f
e
t
y
Observe the following advices in order to protect
yourself and other persons against possible injuries.
Pass the safety instructions on to all persons who
work with the machine.
Keep these safety instructions in a safe place.
Repair works on the device must be carried out by
the manufacturer or by companies appointed by
the manufacturer respectively.
Make yourself familiar with the equipment before using it,
by reading and understanding the operating instructions.
Do not use the machine for unsuitable purposes (see
"Proper use").
Be observant. Attend to what you do. Start working with
rationality. Do not use the device when you are tired or
under the influence of drugs, alcohol or medicaments. One
moment of carelessness when using the device can result
in serious injuries.
Operate the saw dust extraction device only on
− solid
− even
− vibration-free ground.
Sufficient fresh air and light conditions must be provided.
Keep your workplace in an orderly condition! Untidiness
can result in accidents.
Do not operate the saw dust extraction device neither in
moist or wet surroundings nor near inflammable liquids or
gases.
Operating the extraction device is not permitted in
explosive rooms.
15
i
d
u
a
l
r
i
s
k
s
i
d
u
a
l
r
i
s
k
s
i
n
s
t
r
u
c
t
i
o
n
s
i
n
s
t
r
u
c
t
i
o
n
s
Not absorbed shall be:
− spark producing machines or ignition sources.
− wooden and metallic parts.
− explosive and insanitary media as finish fog, gases and
dusts.
Only operate the machine with complete and correctly
attached safety equipment and do not alter anything on the
machine that could impair the safety.
Do not alter the motor controller setting, since the rotary
speed controls the safe maximum operating speed, and
protects the motor and all rotating parts against damage
due to excess speed. Contact the customer service in case
of problems.
Faulty or damaged parts in the device must be replaced
immediately.
Do not leave the machine standing in the rain or use when
raining.
Never leave the machine unattended.
Within his area of work the operator is responsible for third
parties.
Do not allow children to play with this machine.
Keep children away from machine.
Do not allow children to perform cleaning and maintenance
tasks.
Do not spray machine with water (this is hazardous due to
live components).
Keep the device in a safe place. Keep not used devices in
a dry, closed and for children inaccessible room.
Switch the machine off and remove the mains plug from the
socket when
− carrying out repair works
− maintenance and cleaning
− removal of faults
− checking of connection cables whether they are
swallowed or damaged
− transport
− Replacing the saw dust bag
− Leaving
the
machine
interruption)
Check the machine for possible damage:
− Before further use of the machine the protection
devices or slightly damaged parts must be checked
carefully for their proper and intended function.
− Check whether the movable parts function perfectly and
do not stick or whether the parts are damaged, All parts
must be correctly installed and fulfil all conditions to
ensure perfect operation of the machine.
− Damaged protective devices and parts must be repaired
or replaced properly by an approved specialised repair
shop or the manufacturer, unless otherwise indicated in
the instruction manual.
− Damaged or illegible security labels have to be
replaced.
Electrical safety
Design of the connection cable according to IEC
(H 07 RN-F) with a core cross-profile section of at least
− 1.5 mm
for cable lengths up to 25 m
2
− 2.5 mm
for cable lengths over 25 m
2
(also
during
temporary
60 245
Publicité
Table des Matières
