Kenwood KDC-X500 Mode D'emploi page 26

AUDIO SETTINGS
VOLUME OFFSET –15 to +6 (0): Preset the initial volume level of each source.
(Before adjustment, select the source you want to adjust.)
SOUND EFFECT
SOUND RECNSTR (Not applicable for TUNER source, AUX source and SIRIUS XM source.)
(Sound ON: Creates realistic sound by compensating the high-
reconstruction) frequency components and restoring the rise-time of
the waveform that are lost in audio data compression. ;
OFF: Cancels.
SPACE ENHANCE (Not applicable for TUNER source.)
SMALL/ MEDIUM/ LARGE: Virtually enhances the sound
space. ; OFF: Cancels.
SND REALIZER LEVEL1/ LEVEL2/ LEVEL3: Virtually makes the sound more
realistic. ; OFF: Cancels.
STAGE EQ LOW/ MIDDLE/ HIGH: Virtually adjust the sound position
heard from the speakers. ; OFF: Cancels.
DRIVE EQ ON: Boosts the frequency to reduce the noise heard from
outside the car or running noise of the tyres. ; OFF: Cancels.
The frequency and slope settings are automatically set for the
SPEAKER SIZE
crossover of the selected speaker.
FRONT SIZE 3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/
5×7/ 6×8/ 6×9/ 7×10: Selects according
to the connected speaker size for optimum
performance.
TWEETER SMALL/ MIDDLE/ LARGE: Selects according
to the size range of the connected tweeter for
optimum performance. ; NONE: Not connected.
REAR 3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6/ 5×7/ 6×8/
6×9/ 7×10: Selects according to the connected speaker size
for optimum performance. ; NONE: Not connected.
SUBWOOFER 6.5"/ 8"/ 10"/ 12"/ 15" OVER: Selects according to
the connected speaker size for optimum performance. ;
NONE: Not connected.
22
X ' OVER
TWEETER FRQ 1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/
12.5KHZ: Adjusts the crossover frequency for the tweeter speaker.
GAIN LEFT –8 to 0: Adjusts the output volume of the left tweeter.
GAIN RIGHT –8 to 0: Adjusts the output volume of the right tweeter.
FRONT HPF F - HPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/
150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for
the selected speakers (high pass filter). ; THROUGH: All signals are
sent to the selected speakers.
F - HPF SLOPE –6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
(Selectable only if a setting other than [THROUGH] is selected for
[F - HPF FRQ].)
F - HPF GAIN –8 to 0: Adjusts the output volume of the selected speaker.
REAR HPF R - HPF FRQ
R - HPF SLOPE (Refer FRONT HPF settings above.)
R - HPF GAIN
SUBWOOFER SW LPF FRQ 30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/
LPF 150HZ/ 180HZ/ 220HZ/ 250HZ: Adjusts the crossover frequency for
the subwoofer (low pass filter). ; THROUGH: All signals are sent to the
subwoofer.
SW LPF –6DB/ –12DB/ –18DB/ –24DB: Adjusts the crossover slope.
SLOPE (Selectable only if a setting other than [THROUGH] is selected for
[SW LPF FRQ].)
SW LPF REVERSE (180°)/ NORMAL (0°): Selects the phase of the subwoofer
PHASE output to be in line with the speaker output for optimum performance.
SW LPF GAIN –8 to 0: Adjusts the output volume of the subwoofer.
• [SUB-W LEVEL]/ [SUBWOOFER] of [SPEAKER SIZE]/ [SUBWOOFER LPF] of [X ' OVER] is selectable
only if [SUBWOOFER SET] is set to [ON].
• [TWEETER], [REAR HPF] and [SUBWOOFER LPF] of [X ' OVER] is selectable only if a setting other than
[NONE] is selected for [TWEETER], [REAR] and [SUBWOOFER] of [SPEAKER SIZE].