Makita DCW180 Manuel D'instructions page 10

PARTS DESCRIPTION
► Fig.1
1 Control panel
4 Upper cover
7 Opener
10 "DC IN" socket
13 Cool / heat switch button
16 Temperature reduction button
OPERATION
1. Connecting the power supply
A) Battery
CAUTION:
Always switch off the tool before
installing or removing of the battery cartridge.
CAUTION:
Hold the tool and the battery car-
tridge firmly when installing or removing battery
cartridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your hands
and result in damage to the tool and battery cartridge
and a personal injury.
CAUTION:
Be careful not to pinch your finger
when opening or closing the battery cover.
To install the battery cartridge, open the battery
cover.
Align the tongue on the battery cartridge with the
groove in the housing and slip it into place. Insert it
all the way until it locks in place with a little click.
Then close the battery cover.
To remove the battery cartridge, slide it from the
appliance while sliding the button on the front of
the cartridge.
► Fig.2
► 1. Red indicator 2. Button 3. Battery cartridge
CAUTION:
Always install the battery cartridge
fully until the red indicator cannot be seen. If not
it may accidentally fall out of the tool causing injury to
you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
NOTE: Up to two battery cartridges can be installed,
although the appliance uses one battery cartridge for
operation.
B) AC adaptor (Only use for
Recreational vehicle)
When using the appliance with AC power, use the AC
adaptor supplied with the appliance. Insert the plug to
"DC IN" inlet of the appliance and then insert the other
end to an outlet.
2 Battery cover
5 Handle
8 Filter cover
11 Temperature plus button
14 Temperature display
17 USB power supply port
C) Cigarette lighter adaptor
When using the appliance with the cigarette lighter
socket, use the cigarette lighter adaptor supplied with
the appliance. Insert the plug to "DC IN" inlet of the
appliance and then insert the other end to the cigarette
lighter socket.
"DC IN" inlet. Failure to do so may deform the plug
or cause a fire.
cover firmly when the power cord is not plugged.
NOTICE:
for about 24 hours with the battery cartridge
installed, battery cartridge may shut down its
own power to protect the battery cartridge. In this
case, the appliance can not operate with the bat-
tery power supply and the battery indicator also
goes off.
To resume the battery power supply, remove and
re-install the battery cartridge.
NOTE: When the appliance shifts power supply, the
compressor will stop for about 3 minutes to protect the
compressor.
NOTE: After turning off the appliance, it takes about 3
minutes to restart the compressor because of the pro-
tection of the compressor.
2. Turning on the appliance
Press the power button to turn on the appliance. Press
the power button again to turn off the appliance.
3. Switching cooling / heating mode
Press the cool / heat switch button to switch the oper-
ating mode.
The temperature display flashes the control
temperature.
•
•
10 ENGLISH
3 Upper cover hook
6 Carrying Handle
9 Wheel
12 Power button
15 Battery indicator
- -
CAUTION:
Insert the plug completely into the
CAUTION:
Always close the "DC IN" socket
When the appliance has been operated
When the appliance operates in cooling mode, the
control temperature is -18 °C, -10 °C, 0 °C, 5 °C or
10 °C (0 °F, 15 °F, 30 °F, 40 °F or 50 °F).
When the appliance operates in heating mode, the
control temperature is 55 °C or 60 °C (130 °F or
140 °F).