English - Wood's M10 Mode D'emploi

Thank you
Thank you for choosing a Wood's
dehumidifier. You are one of more
than 400.000 people who have cho-
sen a Wood's dehumidifier to prevent
damages from excessive moisture
and mould. Originating in Canada
in 1950, Wood's has more than 60
years experience of developing and
manufacturing dehumidifiers. When
choosing a Wood's dehumidifier
you'll get a unit with great quality,
high capacity and that will extract the
most litres per consumed kWh.
Workings of your
dehumidifier
The Wood's M10 is a compressor
dehumidifier. As the air is drawn
through the dehumidifier by the fan,
the air passes over the compressor
cooled copper coils. The coils cool
the water vapour, separating the
water from the air.
The water drips down from the coils
and is drained away with the water
hose. Left is the dry air that is exhau-
sted in the room. As the dehumidifier
condensates the water vapour, heat
energy is released. That is why a
compressor dehumidifier will exhaust
dry air that is extra beneficial for dry-
ing clothes, laundry, wood etc.
A compressor dehumidifier is the
most energy efficient way to remove
excess moist and bad odour. Keep
the relative humidity level between
50% and 60% to maintain a safe and
healthy indoor environment.
1. Security warnings
Please read the security warnings
carefully before installing and using
the appliance. If the security regula-
tions are not followed, it may void the
product warranty and even present a
fire hazard:
• Unplug the unit from its power
supply before cleaning, storage or
maintenance of its filter.
• This appliance is not intended for
use by persons (including children)

English

with reduced physical, sensory or
mental capabilities, or lack of expe-
rience and knowledge, unless they
have been given supervision or
instructions concerning use of the
appliance by a person responsible
for their safety.
• The appliance shall be installed
in accordance with national wiring
regulations.
• If the supply cord is damaged,
it must be replaced by the ma-
nufacturer, its service agent or
similarly qualified persons in order
to avoid a hazard.
• Always keep a safe distance from
water sources.
• The appliance is a heat source. It
is very important that the applian-
ce isn't covered and that it is kept
away from inflammable materials
and other heat sources.
• Do not put fingers or other
objects into air inlet or air outlet.
• Do not stand on the machine.
• Do not cover the appliance.
• Do not to alter or reconstruct the
appliance or its power cable in any
way.
• Always drain the water
according to the instructions.
• The compressor in the unit is filled
with a freon free refrigerant. If there
is a leakage on the refrigerant
system you should stop using the
appliance and contact your retailer.
• Do not use the appliance without its
air filter.
• The unit generates water, always
keep a safe distance from materials
sensitive to water damage, such as
wooden floors.
2. Installation and
placement
Wood's dehumidifiers are easy to
move around, but bare in mind the
following.
• The dehumidifier should not be
placed near radiators or other
heat sources or exposed to direct
sunlight, as it will reduce its perfor-
4
mance.
• Keep at least 25cm distance from
walls and other obstructions to
maximize the air flow.
• For optimum performance, place
the dehumidifier in the middle of
the room.
• Make sure that the air flow from the
inlet and outlet isn't blocked
Installation:
1. Place the dehumidifier on a flat
and solid ground, preferably in the
middle of the room.
2. Close all windows and ventilators
in the room. Otherwise, moist air
from the outside will continue to flow
into the room.
3. Connect the dehumidifier to a
grounded power outlet.
If the dehumidifier is transported
horizontally, oil may have run out of
the compressor and into the closed
piping system. In such a case, let
the dehumidifier stand for a few
hours before being used. It is very
important that the oil runs back into
the compressor, otherwise the dehu-
midifier may be seriously damaged.
3. Using the M10
Hygrostat controlled
The unit will run only when the
ambient humidity exceeds your set
value.
Automatic restart
In the event of a power failure, the
unit will continue to work according to
your latest settings once the power
returns.
Automatic defrost
The unit will defrost automatically
when needed and resume to work
when the defrost is completed.
When defrosting, the compressor
shuts off and the defrost indication
light is lit.