Important Safeguards; Assembly - Ryobi EWD-1245 Manuel D'utilisation

GB
FR D

IMPORTANT SAFEGUARDS

Ensure that no foreign bodies can get into the
■
openings of the appliance.
Do not change accessories while the appliance is
■
operating.
Always store the appliance indoors. To avoid
■
accidents, put the appliance away safely after use.
The blower can result in foreign objects being
■
blown into eyes, which can result in eye damage.
Always wear eye protection (not provided) when
operating the blower.
Do not permanently cover openings of blower
■
accessories.
Do not point the air outlet openings at people or
■
animals.
Always switch off and unplug Wet/Dry vac from
■
electrical outlet before assembling, opening or
emptying the dust container, or connecting/
disconnecting the attachments.
Keep the suction intake opening free from obstruction
■
at all times; otherwise the motor will overheat and
Wet/Dry vac damage may result.
The Wet/Dry vac is a powerful unit. Before plugging
■
cord into outlet make sure the switch is in the "off"
position. Hold the Wet/Dry vac firmly when starting
and in use.
Keep the mains cable and appliance away from
■
sources of heat.
SAVE THESE INSTRUCTIONS!

ASSEMBLY

CARTON CONTENTS (Fig. 1)
Remove parts from tank and identify the following:
A. Outer tank*
B. Inner tank
C. Cleaner lid and motor housing
D. Caster supports (4)
E. Casters (4)
F. Caster support screws (4)
G. Hose*
H. Extension wands*
I. Utility nozzle**
K. Wet/Dry nozzle**
L. Reusable cartridge filter - assembled to cleaner lid
M. Crevice tool**
N. Squeegee insert**
O. Small foam filter - assembled to inner tank
E I P NL S DK N FIN
English
P Extension wands**
Q. Small float ball
R. Small float cage
S. Outer tank**
T. Adapter**
U. Wet/Dry nozzle with squeegee insert*
V. Hose**
W. Blower nozzle**
X. Large foam filter
Y. Small utility nozzle*
Z. Small crevice tool*
*Provided with EWD1245
**Provided with EWD1260
Note: One of the tool sets shown (either 5.75cm or
3.17cm diameter) is included with your cleaner.
ATTACH CASTER SUPPORTS AND CASTERS
(Fig. 1&2)
Remove cleaner lid and inner tank. Turn outer tank
■
upside down.
Match letters (A or B) on bottom of caster support
■
with letters on cleaner tank.
Align square tabs (1) on supports with rails (2) on tank.
■
Slide tabs onto rails until caster support (3) snaps
in place.
Insert support screw into hole nearest tank.
■
Tighten screw with a Phillips screwdriver.
Repeat with remaining casters and screws.
■
Turn cleaner tank right side up.
ATTACH SMALL FLOAT CAGE (Fig. 3)
Turn inner tank upside down.
■
Place float ball over round opening in bottom of tank.
■
Snap tabs (A) on float cage into slots (B) on tank.
■
Once in place, do not remove the float assembly.
Note: Do not attempt to remove the large filter cage or
float ball on cleaner lid. They are not removable parts.
INSERT INNER TANK (Fig. 4)
With inner tank duct toward drain side of outer tank,
align tab (C) on inner tank with slot (D) in outer tank;
slide inner tank into place.
ATTACH CLEANER LID (Fig. 5)
Rotate lid latches (E) outward. With wet/dry selector
■
(F) toward drain side of tank align ribs (G) on front
of tank with slots (H) on either side of hose inlets;
place lid on tank.
12
GR TR EST LT LV