Disassembling/Assembling - pewag VCW Mode D'emploi

Depending on the faults noted:
• disassemble and clean the clamp (see Chapter 7 – Disassembling/
Assembling) or have the clamp overhauled by pewag austria GmbH
or by another authorised mechanical repair centre (see Chapter 8 –
Overhaul).

7. Disassembling/Assembling

Guidelines for disassembling/assembling of VCW, SVCW, VCEW,
VHPW clamp models
• Open the clamp to its full extent.
• Remove the tension spring (9); in the case of VCW 0.75, VCEW 1 T,
VCW 1.5, VCEW 2+3 T first remove the retaining pin (10) in the cam
assembling.
• Remove the retaining pin (10) and the cam pin (7).
• Push the lifting shackle (5) in until the spindle (6) can be removed via
the assembly hole.
• Remove the lifting shackle (5) and the cam assembling (2).
• Dismantle the lever (4) by removing the retaining pin (10) and taking
the lock assembling (3) out of the clamp.
• Remove the pivot (8) using a socket and ring spanner.
• Clean all parts with a standard degreasant.
• Grease all spindles with a bearing grease.
• Oil the spring if necessary.
• Assemble all the parts in reverse order.
• Always insert new original retaining pins (10) and do so with the aid
of a hammer, combination pliers and pin punch.
• Regularly replace the pivot bolt (11) and nut (12).
• Regularly replace the original pewag components.
• Remove any burr with a file.
Guidelines for disassembling/assembling of VMPW, SVMPW,
VEMPW clamp models
• Open the clamp to its full extent.
• Remove the tension spring (9); in the case of the VMPW 0.75,
VEMPW 1 T, VMPW 1.5, VEMPW 2+3 first remove the retaining pin
(10) from the cam assembling.
• Remove the retaining pin (10) and the cam pin (7).
• Remove the retaining pin (10) and the link pin (14).
• Remove the lifting shackle (5).
• Push the fork (15) in until the shackle pin can be removed via the
assembly hole (6).
• Remove the fork (15) and the cam assembling (2).
• Dismantle the lever (4) by removing the retaining pin (10) and taking
the lock assembling (3) out of the clamp.
• Remove the pivot (8) using a socket and ring spanner.
• Clean all parts with a standard degreasant.
• Grease all spindles with bearing grease.
• Oil the spring if necessary.
• Assemble all the parts in reverse order.
• Always insert new original retaining pins (10) and do so with the aid
of a hammer, combination pliers and pin punch.
• Regularly replace the pivot bolt (11) and nut (12).
• Only use original pewag components.
• Remove any burr with a file.
Guidelines for disassembling/assembling of VUW, SVUW, VEUW,
VUW-R, VHPWU clamp models
• Open the clamp to its full extent.
• Remove the tension spring (9) in the case of the VUW 0.75, SVUW/
VEUW 1 T, VUW 1.5, VEUW 2+3 T first remove the retaining pin (10).
• Remove the retaining pin (10) and the cam pin (7).
3
5
6
2
1
Detail : A
Detail : A
11
8
12
6
2
1
10
Detail : A
Detail : A
10
6
2
1
10
Detail : A
Detail : A
11
8
12
9
10
4
13
10
7
E
5
14
10
15
3
9
10
4
11
8
12
16
17
18
3
9
10
4
13
10
7
13