Bulb Replacement; How To Replace A Worn Belt; To Adjust Or Replace Brush - Oreck XL21 600 ECB Guide D'utilisation

Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in the
efficiency of your ORECK vacuum cleaner. The purpose of the filter bag
is to trap dirt, but at the same time it must be porous enough to allow air
to pass through. If the filter bag becomes clogged, no air can pass
through the cleaner and cleaning cannot take place, regardless of the
cleaner's power.
To keep your cleaner operating at maximum efficiency, change the dust
bag frequently. DO NOT FILL ABOVE THE LINE INDICATED ON THE
DUST BAG.
Be sure the disposable paper filter dust bag is installed properly.
All paper dust bags are not the same. Your ORECK disposable
dust bags have been designed to be used with the ORECK cleaner.
Using bags other than genuine ORECK disposable bags will affect
the cleaning ability of your cleaner and could cause damage to it.
®
HEPA-Celoc Hypo-Allergenic Filter System
The HEPA-Celoc outer bag of your vacuum cleaner is high filtration
medical material designed to filter the smallest of dust particles. It is
important the inside of the outer bag be cleaned. Vacuum the inside of
the outer bag or hand wash, turned inside out, with warm water, and air
dry. If desired, the HEPA-Celoc outer bag can be replaced for renewed
efficiency. The Celoc layered disposable inner dust bag must be
replaced once a month even if it is not full. Change it more often if it is
used in extremely dirty areas. Increase the cleaning power of your
vacuum by changing the bag often.
The Belt
The belt on your vacuum cleaner controls the speed of the revolving
brush and is very important for the effective operation of the cleaner. If
the belt becomes stretched or cut, it will cause the revolving brush to
stop completely or slow down. See instructions in the manual for
replacing belt.
An extra belt is stored in the baseplate of your cleaner. When
buying replacement belts, use ONLY ORECK genuine belts. Belts
other than Oreck belts will not operate the revolving brush
correctly and may create undue stress which will cause damage to
the motor and brush bearings. Using belts other than ORECK belts
will void the warranty.
Motor Filter
The motor filter is used to filter tiny particles released by the motor
exhaust while in operation. The motor filter is not necessary for
operation but is helpful in removing contaminants from the air.
NOTE: Motor filter should be replaced every two months for best
performance.
®
Oreck Fresh Air Cartridges
A fresh air cartridge adds a desired fragrance to the air while
vacuuming. It is placed behind the motor filter and uses heat and air
generated from the motor to spread the fragrance.
NOTE: Cartridge should be replaced every month when filter dust bag
is replaced or as desired.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and sealed.
Further lubrication is not required.
General Cleaner Care
fig. 9 At least once a month, check for and remove excessive lint,
string or hair from revolving brush. Patented cleaning grooves
on brush roll will allow easier cleaning.
Wipe the outside of the cleaner with a damp cloth. Also clean the
connector deflector assembly area, base of cleaner and fan housing
area. If there is dust in the outer bag, vacuum it or shake it out.
A little preventative maintenance will keep your cleaner looking new and
will ensure continued cleaning effectiveness.
CAUTION—Wood Floors, Soft (Vinyl, Asphalt Tile, etc.) Floor
E N G L I
Surfaces and Polished Floor Finishes
Use floor and floor finish manufacturer's recommended methods of
cleaning. The metal strip on the base of the cleaner could be damaged if
used on concrete or abrasive surfaces, and, therefore, cause damage to
wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and polished
floor finishes. The roller brush may also scuff very soft finishes. Do not
operate the unit while in the upright and locked position. Do not let the
unit run while in any one stationary position for any period of time. Keep
the unit moving while in operation.
To Replace Filter Dust Bag
BAG REMOVAL:
fig. 10 Unzip outer bag completely.
fig. 11 Pull bag cardboard collar to release bag dock door from
fig. 12 Gently pull bag cardboard collar upward out of the bag dock.
BAG INSTALLATION:
fig. 13 Slide the cardboard collar completely onto bag dock door.
fig. 14 Firmly push bag dock door with both thumbs on indication point

Bulb Replacement

fig. 15 Remove lamp housing by removing two (2) screws in the top of

How to Replace a Worn Belt

fig. 16 Remove the replacement belt from the storage channel.
fig. 17 Remove the door by removing the hold down screw located on
fig. 18 Fold door away from the power head and lift it away.
fig. 19 Remove the belt from the motor drive shaft and brush roll pulley.
fig. 20 Loop the new belt over the brush roll pulley. Place the opposite
fig. 18 Replace the door by placing the bottom tab on door into slots
fig. 17 Replace the hold down screw and tighten.

To Adjust or Replace Brush

Your Oreck Vacuum comes with the brush roll set at the NORMAL
position for most types of carpets. When using vacuum primarily on
Berber Carpets, adjust brush roll to the SPECIAL setting.
fig. 21 Remove the base plate by removing 5 screws. Then, remove
fig. 22 Rotate both end cards of the brush roll to show "SPECIAL" and
fig. 23 NOTE: The one marked "SPECIAL" has several ribs on top of
fig. 24 The brush end card setting marked "NORMAL" has one rib.
fig. 21 Reassemble the belt and the baseplate.
6
S H
WARNING: Unplug cord from electrical
outlet before servicing.
connector. Bag dock door will hinge downward.
Saniseal ® dust seal will close automatically.
until it snaps.
WARNING: Unplug cord from electrical
outlet before servicing.
the lamp housing. Pull burned out bulb from holder and replace
with new bulb. Replace lamp housing by replacing two screws
in the top of the lamp housing.
WARNING: Unplug cord from electrical
outlet before servicing.
side of power head.
end of the belt on the motor drive shaft.
located inside power head and pressing the door closed.
WARNING: Unplug cord from electrical
outlet before servicing.
the belt and brush roll from the housing.
replace in the holding channels of the housing.
the end card.
When rotating bearings, make sure both end card assembly
settings are the same and face up when replacing the brush roll.