Factory Reset; Troubleshooting; Power Indicator Is Not Illuminated; Fuse Replacement - Rotel A11 Manuel De L'utilisateur

the specified "Off Timer" period the unit will automatically go to STANDBY
mode. The Auto Power Off timer will be restarted if changes are made to
the volume, source or playback. The default for Off Timer is set to 20 MINS.
Valid settings include: DISABLE, 20 MINS, 1 HOUR, 2 HOURS, 5 HOURS,
12 HOURS.
• SIGNAL SENSE: Check if a audio signal is present on the configured
Signal Sense input. The A11 monitors the data stream to determine if
there is audio. If there is no audio detected for 10 minutes, the A11 will
enter Signal Sense Power Mode. When in Signal Sense Power Mode and
the A11 detects audio on Signal Sense input, the unit will automatically
power on. To disable this function, select the OFF option which is the
factory default setting.
NOTE: When the A11 enters standby mode via the remote control,
the Signal Sense function will not operate until the unit detects the
audio has stopped for the minimum 10 minute time-out period. This
prevents the unit from immediately powering back on if there is still
active audio playing.
NOTE: When the SIGNAL SENSE function is activated the A11 will
consume additional power in Signal Sense Power mode.
• FIXED GAIN: Configures a Fixed Volume level for a specified input. To
enable this feature, select the desired fixed volume level for AUX1, AUX2
or Bluetooth. When enabled and the input with a Fixed Volume is selected,
the Volume level will immediately be set to the specified level.
Valid settings include: VARIABLE, FIXED MIN, FIXED 01-95, FIXED MAX.
• AUX1 VOL: VARIABLE (disabled) is factory default.
• AUX2 VOL: VARIABLE (disabled) is factory default.
• BTOOTH VOL: VARIABLE (disabled) is factory default.
NOTE: The Volume knob on the front panel and Volume +/- buttons
on the IR remote are disabled when the volume is Fixed. To disable this
feature set the Fixed Volume level to "Variable".
• S/W VERSION: This shows the current software version loaded into the
amplifier.
• FACTORY RESET: This sets the unit back to the original state as when it
left the factory. Press the + button on the front panel or the ENT button
on the remote control to enter factory reset setting. And then press the +
button or ENT again to begin reset, or press the MENU button to cancel.
NOTE: All previously configured options will be erased and reset to
the factory default settings.

Troubleshooting

Most difficulties in audio systems are the result of incorrect connections, or
improper control settings. If you encounter problems, isolate the area of the
difficulty, check the control settings, determine the cause of the fault and
make the necessary changes. If you are unable to get sound from the unit,
refer to the suggestions for the following conditions:

Power Indicator Is Not Illuminated

The Power Indicator and the basic items in the Display window should be
illuminated whenever the unit is plugged into the wall power outlet and the
Power button is pushed in. If it does not illuminated, test the power outlet
with another electrical device, such as a lamp. Be sure the power outlet
being used is not controlled by a switch that has been turned off.

Fuse Replacement

If another electrical device works when plugged into the power outlet, but
the Power Indicator still will not illuminated when the unit is plugged into
the wall outlet, it indicates that the internal power fuse may have blown.
If you believe this has happened, contact your authorized Rotel dealer to
get the fuse replaced.

No Sound

Check the signal source to see if it is functioning properly. Make sure the
cables from the signal source to the amplifier inputs are connected properly.
Be sure the Input Source is set to the proper input. Check the wiring between
the amplifier and the speakers.

Playable Audio Formats

APTX Bluetooth
Format
Any format supported May exclude Apps designed to play formats not originally
by the sending device. supported by the sending device.

Cannot Connect via Bluetooth

If you cannot pair your Bluetooth enabled device to the A11, delete the
memory of the previous connection on your device. On your device this is
often listed as "Forget this Device". Then try to make the connection again.
13
Notes