Care Of Your Press & Refresh; Troubleshooting Guide - shark Press & Refresh GS500CWN Guide D'utilisation

Using Your Press & Refresh
When to use the different
accessories:
1
Small Steam Bonnet – must 4 Upholstery/Delicate Fabric
be in place over steam nozzle Frame & Delicate Steam
during all usage. Bonnet – provides extra
protection for delicate fabrics
TIP: Provides evenly distribution
when the Wrinkle Eraser
of steam and protects fabrics
not necessary while freshening
from watermarks and impurities
fabrics.
in water
Fabric Recommendations:
Silk, satin, embellished
garments.
TIP: Some garments have
better results when steamed
from the inside or turned inside
out. Slightly tug the bottom
of the garment and hold at an
2 Bristle Brush Frame – Offers
angle.
better steam penetration for
heavy fabrics without leaving
water marks.
Fabric Recommendations:
Heavy fabrics, cotton, wool,
canvas, denim.
C AUTION: Do not use the
bristle brush on delicate fabrics.
5 Upholstery/Delicate Fabric
Frame & Upholstery Steam
Bonnet – shaggy material acts
like multiple fingers to pick
up dust and deodorize while
steaming. It provides a large
pocket of hot steam.
3 Lint Brush Frame – use to
remove hair, lint and pet fur
while steaming your garments.
12
TOLL FREE: 1-800-396-9208
GS500CWN_11_IB_EF_100920.indd 12-13
- cont.
™
6 V ELCRO ® Clips –
Easy detachable clips can
be used to hold lightweight
garments directly on to the pad
™ is and to position & stretch the
garment for quick steaming
with better results
7 Vertical Press Pad –
Creates a vertical ironing board
anywhere in the home. The
Vertical Press Pad can be used
on any door and is virtually
invisible when the door is closed
for easy access to the pad for
last minute touch ups.
Care of Your Press & Refresh
Cleaning & storing 6 B undle up the power cord and
secure it with the VELCRO
1 T urn the garment steamer off
strap that is attached to the
"O".
power cord. Always store your
2 U nplug the appliance from the
appliance in a cool, dry area.
electrical outlet.
Care & use of the small steam
3 L et the appliance cool
bonnet frame
completely for approximately
7
T he steam bonnet is attached
30 minutes.
to a frame and helps filter
4 E mpty the water from the
impurities from your water.
water tank.
It might become slightly
discolored over time.
5 W ipe the exterior of the
garment steamer with a damp
8 L et the steamer cool completely
cloth and wipe dry if needed.
before removing. Gently pull on
either side of the frame and lift
off of the nozzle.

Troubleshooting Guide

PROBLEM POSSIBLE REASONS
The steamer is not turned on.
There is no
steam.
There is not enough
water in the unit.
You are not using the steam
bonnet.
The nozzle leaves
The steam bonnet is
water drops on the
too wet.
garment.
The frame has condensation.
English
™
9 H and wash the bonnet frame
in cold water with a mild
®
detergent and let air dry
completely before using again.
Do not dry in clothes dryer.
10 T o re-attach the frame, gently
snap the frame over the steam
nozzle and press gently to lock
into place (Fig. 1).
Fig. 1
SOLUTIONS
Verify that the blue light on the unit is lit. If not,
check that the unit is plugged in and the on/off
button is raised and in the on "I" position.
Verify that the water tank is at least half way full
or fill to the max fill line.
The small steam bonnet frame must be in place
at all times during usage.
The bonnet prevents water drops being left on
the garment and to removes impurities from your
water.
Let the unit cool for 30 minutes, remove the
steam bonnet and let it dry out before using
again or replace with a new bonnet frame.
Let the appliance cool and wipe the frame off.
13
www.sharkclean.com
20/09/10 9:37 AM