Publicité
English
Our products are engineered to meet the highest
standards of quality, functionality and design. We hope
you thoroughly enjoy your new Braun coffee mill.
Caution
Read all instructions carefully before using this
product.
• This appliance is for household use. It must be kept
out of the reach of children!
• Before plugging into a socket, check whether your
voltage corresponds with the voltage printed on the
bottom of the appliance.
• Always unplug the appliance before cleaning, and
before removing the coffee bean receptacle from
the motor block.
• Braun electric appliances meet applicable safety
standards. Repairs on electric appliances must only
be done by authorized service personnel.
• Faulty, unqualified repair work may cause accidents
or injury to the user.
• The cord of the appliance may only be replaced by
an authorized Braun Service Centre as a special tool
is required.
Description
1
On/off switch and timer/measurer
(the appliance is switched off at setting
«timer off/0»)
2 Motor block
3
Grind fineness scale
4
Grind selector ring
5
Coffee bean receptacle
6
Lid for the coffee bean receptacle
7 Fineness marker on the grind selector ring
8
Lid for the coffee grounds receptacle
9
Coffee grounds receptacle
j
Measuring spoon with cleaning spatula
Plugging in
Pull out only as much cord from the cord storage as you
need to the socket (a).
Grinding coffee
Notice: To retain the full flavour of the coffee beans,
the coffee bean receptacle should be always properly
closed with the lid.
Only the immediately needed quantity of coffee should
be ground at a time.
Setting the degree of fineness:
The grind fineness scale has two general sections: one
for filter coffee («filter coffee») and one for espresso-
type coffee («espresso»).
Set the desired degree of coffee grounds fineness by
turning the grind selector ring so that the fineness
marker points to the desired dot on the grind fineness
scale (b).
The grind selector ring
block and can be turned from one end of the grinding
fineness spectrum to the other. If you turn the grind
selector ring anti-clockwise, the grind will be coarser
5
9
4
is screwed into the motor
the higher the figures and the larger the dots on the
grind fineness scale are.
Notice: When using a coffeemaker, the coffee grounds
should not be too fine, as this could result in the
coffeemaker overflowing, as water would not be able to
flow as designed through the filter. For espresso-type
coffee you should try starting with a medium setting in
the «espresso» section of the grind fineness scale, and
adjust so that two cups of espresso takes approxi-
mately 25 seconds to brew, once the coffee starts to
drip out of the filter of your espressomaker.
Turning on the coffee mill:
The coffee mill is switched on by turning the switch
clockwise. Turn the switch until you have reached the
right setting for the desired quantity of coffee grounds
(c). The marking numbers are shown on the timer scale
around the timer switch.
By returning the on/off switch to position «timer off/0»,
you may stop or shorten the grinding process at any
time.
Removing the coffee grounds
When grinding is completed, remove the lid from the
coffee grounds receptable and take out the coffee
grounds with the measuring spoon.
The coffee grounds receptacle can also be pulled off
from the motor block horizontally (d). A measuring
spoon full of coffee grounds is approximately 6.5 g,
generally the quantity needed for 1 cup of brewed
coffee or espresso.
4
Cleaning
Before cleaning, always first unplug the appliance.
Do not immerse the motor block in water and do not
hold it under running water. Wipe the motor block with
a damp cloth only.
The coffee grounds outlet can be cleaned with the
spatula on the reverse end of the measuring spoon (e).
The coffee bean receptacle, the lid, the coffee grounds
receptacle and the lid may be cleaned in the
dishwasher.
Subject to change without notice.
This product conforms to the EMC-Requirements
as laid down by the Council Directive 89/336/EEC
and to the Low Voltage Regulation (73/23 EEC).
5
Publicité
