Transporting The Machine; Before Initial Operation - Viking MI 632 Manuel D'utilisation

Store the battery out of the reach of
children.
Explosive hazard!
Protect the battery
against direct sunlight,
heat and fire – never
throw it into a fire.
Only use or store the battery at
temperatures from -10°C to max.
+50°C.
Protect the battery against rain
and moisture – do not immerse in
liquids.
Do not subject the battery to
microwaves or high pressure.
Never connect the battery terminals with
metallic objects (short-circuit). The battery
can be damaged through short circuits.
Keep the unused battery away from
metallic objects (e.g. nails, coins,
jewellery). Do not use metallic transport
containers – Explosive and fire hazard!
Fluid may escape from the battery due to
improper use – Avoid contact! In the case
of inadvertent contact, rinse with water.
Seek medical attention if the fluid contacts
the eyes. Escaping battery fluid can cause
skin irritation and burns.
Do not insert any objects in the ventilation
slots of the battery.
For further safety instructions, see
www.viking-garden.com/safety-data-
sheets

6.5 Transporting the machine

Before transporting, and especially before
lifting the robotic mower, activate the
disabling device. ( 5.2)
98
Allow the machine to cool down before
transporting.
Avoid contact with the mowing blade when
lifting and carrying the machine. The
robotic mower must only be lifted at the
carrying handle. Never reach under the
machine.
Take the weight of the machine into
account and use suitable loading aids
(lifters) if required.
Secure the machine and other machine
parts being transported (e.g. docking
station) on the load floor using fastening
materials (straps, ropes, etc.) of an
adequate size at the fastening points
described in this instruction manual.
( 21.)
When transporting the machine, always
observe regional legislation, especially
regarding load security and the transport
of objects on load floors.
Do not leave the battery inside a vehicle
and never expose it to direct sunlight.
Lithium-ion batteries must be treated with
special care during transport. In particular,
short-circuit protection must be ensured.
Transport the battery either in the original
packaging or in the robotic mower.

6.6 Before initial operation

It must be ensured that all persons who
use the machine are familiar with the
instruction manual.
Carefully follow the instructions for
installing the docking station (
perimeter wire ( 12.).
The perimeter wire and the power cable
must be securely fastened to the ground
so that they do not present a tripping
hazard. Avoid routing the perimeter wire
and power cable over edges (e.g. edges of
pathways or paving stones). When routing
the perimeter wire and power cable on
ground into which the supplied fixing pins
cannot be driven (e.g. paving stones,
pathways), a cable duct must be used.
Correct routing of the perimeter wire and
power cable must be regularly checked.
To prevent the risk of stumbling, always
drive in the fixing pins all the way.
Do not install the docking station in a place
where it is difficult to see and could
become a tripping hazard (e.g. around the
corner of a house).
If possible, install the docking station out of
the reach of pests such as ants or slugs –
in particular avoid the area around anthills
and composting units.
Areas in which the robotic mower cannot
operate safely (e.g. due to danger of
falling), must be blocked off through
appropriate routing of the perimeter wire.
VIKING recommends that the robotic
mower is only operated on lawns and
surfaced paths (e.g. paved drives).
The robotic mower does not detect any
sudden drops such as edges, steps,
swimming pools or ponds. If the perimeter
wire is routed along potential sudden
drops, a clearance of at least 1 m must be
maintained between the perimeter wire
and the danger area for safety reasons.
Regularly inspect the area on which the
machine is to be used and remove any
sticks, stones, wires, bones and all other
9.6) and
foreign objects that could be thrown up by
the machine.
After installing the perimeter wire,
particularly remove all tools from the
0478 131 9933 A - EN