Elica SPACE Série Prescriptions De Montage Et Mode D'emploi page 17

3. Speed (power) suction selection key 1: press once to
select the suction speed (power), press again and keep it
pressed to activate 20 minute (flashing key) functioning
time, after which the hood turns off (Stand by)
4. Speed (power) suction selection key 2: press once to
select the suction speed (power), press again and keep it
pressed to activate 15 minute (flashing key) functioning
time, after which the hood turns off (Stand by)
5. Speed (power) suction selection key 3: press once to
select the suction speed (power), press again and keep it
pressed to activate 10 minute (flashing key) functioning
time, after which the hood turns off (Stand by).
6. Intensive suction speed (power) ON/OFF selection
key (timed): press to select the suction speed (power).
Functioning time is 5 minutes after which suction turns off
or returns to the speed (power) previously selected.
7. COMFORT button: the hood begins to operate in a
"cyclical" manner when filtering the air, which means the
motor is activated at speed level 1 for 5 minutes and then
switched OFF for 30 minutes. This operating mode
remains set until the OFF button (or any of the speed
buttons) is pressed; this will stop the COMFORT function
and activate the motor at the selected speed level.
8. Reset saturation filters key: the hood, through the
signal of this luminous key, tells the user when it is
necessary to carry out maintenance of the fat filters and
the carbon filter.
Key lit in green: carry out maintenance of the fat filters,
after which press the key for about 3 seconds and the
key turns off.
Key lit in red: carry out maintenance of the carbon filter,
after which press the key for about 3 seconds and the
key turns off.
Attention: the hood is preset only for signaling the fat
filters.
To enable the signaling of the carbon filter: Set the
hood on OFF, press key 8 for 3 seconds. The key turns
on in red to signal that the setting has taken place. To
disenable the carbon filter signal, repeat this operation
again (the key lights up in green).
Note: A beep sounds each time this key is pressed.
Maintenance
ATTENTION! Before performing any maintenance operation,
isolate the hood from the electrical supply by switching off at
the connector and removing the connector fuse.
Or if the appliance has been connected through a plug and
socket, then the plug must be removed from the socket.
Cleaning
The cooker hood should be cleaned regularly (at least with the
same frequency with which you carry out maintenance of the
fat filters) internally and externally. Clean using the cloth
dampened with neutral liquid detergent. Do not use abrasive
products. DO NOT USE ALCOHOL!
WARNING: Failure to carry out the basic cleaning
recommendations of the cooker hood and replacement of the
filters may cause fire risks.
Therefore, we recommend observing these instructions.
The manufacturer declines all responsibility for any damage to
the motor or any fire damage linked to inappropriate
maintenance or failure to observe the above safety
recommendations.
Grease filter
Fig. B
This must be cleaned once a month (or when the filter
saturation indication system – if envisaged on the model in
possession – indicates this necessity) using non aggressive
detergents, either by hand or in the dishwasher, which must
be set to a low temperature and a short cycle.
When washed in a dishwasher, the grease filter may discolour
slightly, but this does not affect its filtering capacity.
Remove the filter holder frame by turning the knobs (g) 90°
that affix the chimney to the cooker hood.
Charcoal filter (filter version only)
Fig. C
It absorbs unpleasant odours caused by cooking.
The charcoal filter can be washed once every two months (or
when the filter saturation indication system – if envisaged on
the model in possession – indicates this necessity) using hot
water and a suitable detergent, or in a dishwasher at 65°C (if
the dishwasher is used, select the full cycle function and leave
dishes out).
Eliminate excess water without damaging the filter, then put it
in the oven for 10 minutes at 100° C to dry completely.
Replace the mattress every 3 years and when the cloth is
damaged.
Assembly
Place the mat around the grease filter and fix it in place using
the devices provided.
Position the upper cap and fix it in place using the fixing pin.
To disassemble, perform the steps in the reverse order.
Replacing lamps
The hood is equipped with a lighting system based on LED
technology.
The LEDs guarantee an optimum lighting, a duration up to 10
times as long as the traditional lamps and allow to save 90%
electrical energy.
For replacement, contact the technical service.
17