Milwaukee 2475-20 Manuel De L'utilisateur page 4

ASSEMBLY
Recharge only with the charger
WARNING
specified for the battery. For spe-
cific charging instructions, read the operator's
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
Always remove battery pack before
WARNING
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
Only use accessories specifically
WARNING
recommended for this tool. Others
may be hazardous.
Battery Indicator
The Battery Indicator is displayed when the tool is
on. When the battery power is very low
battery indicator will flash.
Setting the Units (PSI, BAR or kPa)
To select the desired unit of pressure, press and hold
the and buttons until the units of measure
begin to flash (about 1.5 seconds). Use the
buttons to scroll through the units (PSI, BAR or
kPa) to select. After about 3 seconds, the screen will
return with the new unit of pressure displayed.
Temperature Protection
During extended use or constricted air flow, the tool
temperature may rise. If the Temperature Protection
Indicator comes on, allow the tool to cool at least
10 minutes before continuing. In extremely low tem-
peratures, the Temperature Protection Indicator
may come on if the battery is too cold.
Allow tool to cool for 10 minutes
CAUTION
after each 10 minutes of continuous
use.
Overload Warning
If airflow is constricted during use, the Overload
Warning Indicator
nections for blockages before continuing use.
Accessories/Hose Storage
Accessories provided with the inflator can be stored
on the back of the tool. The hose can be wrapped
around the storage area and secured in the hose
clamp.
may come on. Check all con-
WARNING
with side shields.
Only use accessories specifically recommended
for this tool. Others may be hazardous.
Do not leave the tool unattended during operation.
Risk of Bursting. Do not overinflate. Follow all
manufacturer's instructions for the item.
1. Place the tool on flat surface.
2. Insert the proper accessory for the item to be
inflated.
3. Attach the accessory to the item to be inflated.
• Always attach the inflator to desired object before
starting inflation.
• No accessory is needed for common car/truck
tire schrader valves.
, the
• For car/truck tires, screw schrader chuck onto
tire valve and ensure it is tight.
4. Insert the battery pack.
5. To turn on, press the
Power button. The tool
will detect the current air
and
pressure of the item.
6. Use the
tons to set the target
pressure, if desired.
Press and hold
buttons to jump down or
up faster.
NOTE: Setting target
pressure is not recommended when using the
accessory nozzles.
NOTE: If the current pressure item to be inflated
is greater than the target pressure, the tool will not
begin inflation.
7. To start, press the Inflation
NOTE: Flashing dashes during inflating or con-
necting indicate the tool is recalibrating pressure.
8. The tool will shut off automatically once the target
pressure has been reached. Target mode shows
- - if no target pressure is set. Inflator will run until
120 psi max pressure.
CAUTION: Allow tool to cool for 10 minutes after
each 10 minutes of continuous use.
9. To stop, press the Inflation
button.
NOTE: The tool will shut down after 5 minutes of
inactivity.
If pressure accuracy becomes poor or the inflator's
actual value reads greater than zero when not con-
nected to any object, the pressure sensor may have
drifted due to altitude or other factors.
To reset:
With nothing connected to inflator, hold power
button and press the
sure to zero.
Sports Needle/Raft Nozzle
Insert needle or nozzle into the item to be inflated.
Be careful not to bend the accessory. Remove after
inflation.
4
OPERATION
To reduce the risk of injury, always
wear safety goggles or glasses
Using the Inflator
and but-
or
Troubleshooting
button 3 times to reset pres-
button.
button or power