Before Starting The Equipment; Operation - EINHELL GE-CM 36/37 Li Mode D'emploi D'origine

Limit the operating time.
All stages of the operating cycle must be
considered (for example, times in which the
electric tools are switched off and times in which
the tool is switched on but operates without load).

5. Before starting the equipment

The lawn mower is delivered partly assembled.
The push bar and the grass basket must be
assembled before using the lawn mower. Follow
the instructions step by step and refer to the
pictures when assembling.
Important! Required assembly parts (screws,
cable guides, etc.) or functional parts (e.g. plugs,
wrenches, etc.) can be found in the molded parts
of the packaging or on the equipment.
The cable for the electrical connection of the
motor and switching bar is located on the left-
hand teeth of the handlebar adjustment facility
(Fig. 3). Take care to ensure that this is not
damaged during assembly.
Fitting the push bar
Use the quick-tightening screws (Fig. 2/Item 16)
to fasten the push bar (Fig. 4/Item 13) to the teeth
of the handlebar adjustment facility. If necessary,
turn the quick-tightening screw back suffi ciently
on the thread so that the quick-release lever
(Fig. 4/Item 16) can then be fl ipped towards the
back.
You can adjust the angle of the long handle as a
whole by fl ipping up the two quick-release levers
(Fig. 5/Item 16), with two settings available for
the angle (Fig. 5). Only these two positions are
available. As you do this, make sure that both
sides are set to the same position. To secure the
push bar again, fl ip the two quick-release levers
back into the closed position.
You can adjust the angle of the upper push bar
by fl ipping up the two upper quick-release levers
(Fig. 6/Item 16), with three settings available for
the angle (Fig. 6a). As you do this, make sure that
both sides are set to the same position. To secure
the push bar again, fl ip the two quick-release
levers back into the closed position.
Fitting the catch basket
Press the carry-handle (Fig. 7/Item 10) onto the
top part of the housing of the catch basket. During
assembly, make sure that there is an audible click.
Anl_GE_CM_36_37_Li_USA.indb 14 Anl_GE_CM_36_37_Li_USA.indb 14
EN
Before you fi t the catch basket you must ensure
that the motor is switched off and the blade is not
rotating. Lift the ejector fl ap (Fig. 8/Item 7) with
one hand. Using the other hand, grab onto the
basket by the handle and hang it in from the top.
Filling level indicator of the grass collector
The grass collector is equipped with a fi lling
level indicator (Fig. 9/Item 12). which is opened
by the airfl ow that the lawn mower generates
during operation. If the fl ap closes during mowing,
the grass collecting device is full and must be
emptied. To ensure the proper functioning of the
fi lling level indicator, the holes under the fl ap must
always be kept clean and passable.
Adjusting the cutting height
Caution!
Adjust the cutting height only when the machine
has been switched off and the safety plug has
been pulled out.
The cutting height is adjusted as follows (see
Fig. 10):
1. Push the lever (7) outwards.
2. Set the lever (7) to the desired cutting height.
3. Release the lever (7) and check that it is
securely seated in the lock.
Reading off the cutting height
The cutting height can be set between 1 - 2.95 in.
(25-75 mm) in 6 intervals, and can be read off on
the scale.
Before you begin to mow, check to ensure that the
blade is not blunt and that none of the fasteners
are damaged. To prevent any imbalance, replace
blunt and/or damaged blades. To carry out this
check, fi rst switch off the motor and pull out the
safety plug.

6. Operation

Caution!
The device is equipped with a safety switch to
prevent unauthorized use. Immediately before
using the equipment, insert the safety plug.
Remove the safety plug again when interrupting
or terminating your work. To do so, press the lug
(Fig. 13/Item 17).
- 14 -
23.09.2020 11:17:45 23.09.2020 11:17:45