Specific Safety Rules - Makita BST221 Manuel D'instruction

14. Do not use tool if switch does not turn it on or
off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
15. Disconnect battery pack from tool or place the
switch in the locked or off position before
making any
accessories,
preventive safety measures reduce the risk of
starting the tool accidentally.
16. Store idle tools out of reach of children and
other untrained persons. Tools are dangerous in
the hands of untrained users.
17. When battery pack is not in use, keep it away
from other metal objects like: paper clips,
coins, keys, nails, screws, or other small metal
objects that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause sparks, burns, or a
fire.
18. Maintain tools with care. Keep cutting tools
sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are
easier to control.
19. Check for misalignment or binding of moving
parts, breakage of parts, and any other
condition that may affect the tool's operation.
If damaged, have the tool serviced before
using. Many accidents are caused by poorly
maintained tools.
20. Use only accessories that are recommended
by the manufacturer
Accessories that may be suitable for one tool may
create a risk of injury when used on another tool.
SERVICE
21. Tool service must be performed only by
qualified repair
maintenance performed by unqualified personnel
could result in a risk of injury.
22. When servicing a tool, use only identical
replacement parts. Follow instructions in the
Maintenance section of this manual. Use of
unauthorized
Maintenance instructions may create a risk of
shock or injury.

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to cordless stapler safety rules. If you use this tool
unsafely or incorrectly, you can suffer serious
personal injury.
adjustments,
or storing the tool.
for your
personnel. Service
parts or failure
1. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and shock
changing the operator.
Such 2. Always wear safety goggles or safety glasses
with side shield, and a full face shield when
needed.
3. Do not point the ejection port at anyone in the
vicinity (especially his face). Keep hands and
feet away from the ejection port area.
4. Always remove the battery cartridge before
loading the staples, adjustment, inspection,
maintenance or after operation is over.
5. Make sure no one is nearby before operation.
Never attempt to drive staples from both the
inside and outside of wall at the same time.
Staples may rip through and/or fly off,
presenting a grave danger.
6. Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations.
7. Check walls, ceilings, floors, roofing and the
like carefully to avoid possible electrical shock,
gas leakage, explosions, etc. caused by
stapling into live wires, conduits or gas pipes.
8. Use only staples specified in this manual. The
use
malfunction of the tool.
model. 9. Do not tamper with the tool or attempt to use it
for other than driving staples.
10. Do not operate the tool without staples. It
shortens the service life of the tool.
11. Stop driving operations immediately if you
or notice something wrong or out of the ordinary
with the tool.
12. Never staple into any materials which may
allow the staple to puncture and fly through as
a projectile.
13. Never actuate the switch trigger and safety
to follow lever at the same time until you are prepared
to staple workpieces. Allow the workpiece to
depress the safety lever. Never defeat its
USB074-2
purpose by securing the safety lever back or
by depressing it by hand.
14. Never tamper with the safety lever. Check the
safety lever frequently for proper operations.
SAVE THESE INSTRUCTIONS.
3
of any other staples may cause