Bosch POF 1200 AE Notice Originale page 18

OBJ_BUCH-323-006.book Page 18 Tuesday, July 15, 2014 1:39 PM
18 | English
Material Router bit
diameter (mm)
Hardwood 4 – 10
(Beech) 12 – 20
22 – 40
Softwood 4 – 10
(Pine) 12 – 20
22 – 40
Particle Board 4 – 10
12 – 20
22 – 40
Plastics 4 – 15
16 – 40
Aluminium 4 – 15
16 – 40
Switching On and Off
Adjust the depth-of-cut before switching on or off; see Sec-
tion "Adjusting the Depth-of-cut".
To start the machine, first push the lock-off button for the
On/Off switch 1 and then press the On/Off switch 22 and
keep it pressed.
POF 1400 ACE: A lamp illuminates the routing area.
To switch off the machine, release the On/Off switch 22.
POF 1400 ACE: The lamp slowly goes out.
Note: For safety reasons, the On/Off switch 22 cannot be
locked; it must remain pressed during the entire operation.
To save energy, only switch the power tool on when using it.
Constant Electronic Control (POF 1400 ACE)
Constant electronic control holds the speed constant at no-
load and under load, and ensures uniform working perfor-
mance.
Adjusting the Depth-of-cut (see figure D)
 The adjustment of the depth-of-cut may only be carried
out when the router is switched off.
For coarse adjustment of the depth-of-cut, proceed as follows:
– Place the machine with the router bit mounted on the
workpiece to be machined.
– POF 1400 ACE: Set the fine-adjustment path to the centre
position with the adjustment knob 18. For this, turn the
adjustment knob 18 until the marks 19 match as shown in
the figure. Afterwards, set the scale 17 to "0".
19
– Set the step buffer 9 to the lowest position; the step buffer
engages noticeably.
– POF 1200 AE: Screw the adjusting screws for the step
buffer 24 halfway in or out.
1 609 92A 0SG | (15.7.14)
– Loosen the wing bolt for the depth stop 11 so that the
Thumbwheel 23
depth stop 13 can be moved freely.
– Push the clamping lever for locking of routing depth 16 in
5 – 6
rotation direction  and and slowly lower the plunge rout-
3 – 4
er until the router bit 21 touches the surface of the work-
1 – 2
piece. Let go of the clamping lever 16 again to lock this
5 – 6
plunging depth.
3 – 6
If required, push the clamping lever 16 in rotation direc-
1 – 3
tion  to lock it in place.
3 – 6
– Push the depth stop 13 downward until it rests on the step
2 – 4
buffer 9. Set the slide with the index mark 12 to the "0" po-
1 – 3
sition on the scale for the depth-of-cut adjustment 14.
– Set the depth stop 13 to the required depth-of-cut and
2 – 3
tighten the wing bolt for the depth stop 11. Pay attention
1 – 2
not to misadjust the slide with the index mark 12 again.
1 – 2
– Push the clamping lever 16 in rotation direction  and
1
guide the router to the uppermost position.
For deep cuts, it is recommended to carry out several cuts,
each with little material removal. By using the step buffer 9,
the cutting process can be divided into several steps. For this,
adjust the desired depth-of-cut with the lowest step of the
step buffer and select the higher steps first for the initial cuts.
POF 1200 AE: The clearance of the steps can be changed by
screwing the adjusting screws 24 further in or out.
Fine Adjustment of the Depth-of-cut (POF 1400 ACE)
After a trial cut, the depth-of-cut can be set exactly to the de-
sired measure by turning the adjustment knob 18; turn in
clockwise direction to increase the cutting depth and in anti-
clockwise direction to decrease the cutting depth. The scale
17 can be used for guidance. One full turn corresponds with a
setting range of 2.0 mm; a graduation mark on the top edge of
the scale 17 corresponds with a 0.1 mm change of the setting
range. The maximum setting range is ± 8 mm.
Example: The desired depth-of-cut is to be 10.0 mm; the trial
cut resulted in a cutting depth of 9.6 mm.
– Lift up the router and place, e. g., a piece of scrap wood un-
der the guide plate 7 so that the router bit 21 cannot touch
the workpiece when lowering it. Push clamping lever 16 in
rotation direction  and slowly lower the plunge router un-
til the depth stop 13 faces against the step buffer 9.
– Turn the scale 17 to "0" and loosen wing bolt 11.
– Turn the adjustment knob 18 by 0.4 mm/4 graduation
marks (difference from set to actual value) in clockwise di-
rection and tighten the wing bolt 11.
– Check the selected depth-of-cut by carrying out another
trial cut.
After adjusting the depth-of-cut, do not change the position of
the slide 12 on the depth stop 13 any more, so that the actual
cutting depth can be read on the scale 14.
Fine Adjustment of the Depth-of-cut (POF 1200 AE)
Different depths-of-cut can be preset with the step buffer 9.
The adjustment is carried out in the same manner as previous-
ly described, with the difference that by screwing the adjust-
ing screws 24 in or out, the height difference between the
stops can be changed.
Bosch Power Tools