Important Safeguards - Tristar KA-5032 Manuel D'utilisation

Operation and maintenance
Remove all packaging of the device.
Check if the voltage of the appliance corresponds to the main voltage of your home.
Rated voltage : AC220-240V 50Hz. Make sure the device will not be submerged in water or
other liquids. If the device has fallen into the water first pull the plug from the outlet. Place the
device on a flat stable surface and ensure a minimum of 50 cm. free space around the device.
This device is not suitable for installation in a cabinet.
Use
When the device is switched on for the first time, a slight smell may be emitted. This is a
normal situation, please ensure sufficient ventilation. This smell will disappear very quickly.
Function switch (No. 3)
I
Low heat output, 1000 watt
II
High heat output, 2000 watt
O
OFF
Thermostat switch (No. 4)
Left Minimum
Right Maximum
If you have selected low or high output, choose the desired temperature with the thermostat
switch (No. 4). With the thermostat, the temperature can be regulated. When the desired
temperature is reached, the unit automatically switch off. Once the temperature has fallen
below the pre-set level, the heater will switch on again. The control light (No. 1) will allow you
to check the thermostatic regulation. When the device is heating, this pilot light will be on. It will
go out when the desired temperature is reached.
Do not cover the device with cloths or any other combustible items.
The grid (No. 4) of the device will be very hot do not touch it.
The exterior of the device is hot. Avoid any physical contact, you can seriously get
injured. Let it cool down completely before it will be moved. Always use the handle
at the top of the device to move.
Cleaning the device
Always switch the device off and disconnect the power cord before cleaning. Let the device
cool down completely. Never immerse the device in water or other liquid.
Clean the housing of the device with a damp cloth.
Regularly remove with a vacuum cleaner dirt and vermin behind the grid (No. 4) of the device.
7
UK

IMPORTANT SAFEGUARDS


Read all instructions before use.

Do not touch hot surfaces. Use handles or knobs.

To protect against electric shock, do not immerse cord, plug or appliance in water or
any other liquid.

Unplug from outlet when not in use and before cleaning. Allow the device to cool
before putting on or taking off parts. Do not operate any appliance with a damaged
cord or plug or after the appliance malfunctions, or has been damaged in any
manner.

The use of accessory attachments not recommended by the appliance manufacturer
may cause injuries and invalidate any warranty you may have.

Do not use outdoors, or on or near direct heat sources

Do not let cord hang over edge of table or counter, or touch hot surfaces or come
into contact with the hot parts or allow the product to be situated underneath or close
to curtains, window coverings etc.

This appliance is for household use only and only for the purpose it is made for.

The appliance must be placed on a stable, level surface.

This appliance is an attended appliance, and as such should never be left ON or
whilst hot without adult supervision.

This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

This device is not intended for use with an external timer or a remote control system.

Note: To avoid danger by the accidental resetting thermal protection, the device may
not be powered through an external switching device, such as a timer, or connected
to a circuit and is turned regularly by the subject.

This device is not intended for use with an external timer or a remote control system.

Note: To avoid danger by the accidental resetting thermal protection, the device may
not be powered through an external switching device, such as a timer, or connected
to a circuit and is turned regularly by the subject.

A damaged cord or plug must be replaced by an authorized technician to avoid a
hazard. Do not repair the device yourself.

Using an extension cord or something similar is not allowed.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
8