Technical Data; Before Starting The Equipment - EINHELL RG-ES 1433 Mode D'emploi

Anleitung_RG_ES_1433_SPK1__ 13.11.13 09:52 Seite 14
GB

4. Technical data

Voltage:
Power consumption:
Working width:
Number of blades:
Scarifying depth:
L sound pressure level:
pA
L sound power level:
WA
K uncertainty:
Vibration on the shaft a
hv
K uncertainty:
Protection class:
Protection type:
Weight:
Total vibration values (vector sum of three directions)
determined in accordance with EN 60335.
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with other electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n
14
230 V ~ 50 Hz
1400 W
33 cm
20 pieces
- 3 / 3 / 7 / 9 mm
76.1 dB(A)
99 dB(A)
2 dB(A)
: 3.159 m/s
1.5 m/s
II /
IPX4
13 kg

5. Before starting the equipment

The scarifier is delivered unassembled. The grass
basket and the complete push bar must be
assembled and mounted before using the scarifier.
Follow the operating instructions step-by-step and
use the pictures provided as a visual guide to easily
assemble the machine.
Fitting the push bar brackets (see Figs. 4 and 5)
Remove the star screw (Fig. 4/Item 1) and the
n
pressure plate (Fig. 4/Item 2)
Connect the push bar bracket (Fig. 4/Item 3) to
n
the fastening screw. Ensure that the curve in the
tube (Fig. 5/Item 1) is facing outside.
2
Now remount the pressure plate and tighten with
n
2
the star screw. Important. The identical tilt angle
must be set for both push bar brackets.
Fitting the lower push bar (see Fig. 6)
Slide the lower push bar (Fig. 6/Item 1) over the
n
push bar brackets.
Do not forget to slide the stress-relief clip (Fig.
6/Item 2) onto the tube beforehand.
Now screw the tubes together using the screws
n
supplied (Fig. 6/Item 3), the plastic sleeves (Fig.
6/Item 4) and the star screw (Fig. 6/Item 5).
Fitting the upper push bar (see Fig. 7)
Position the upper push bar (Fig. 7) such that its
n
holes line up with the holes of the lower bar.
Now screw the tubes together using the screws
n
supplied (Fig. 7/Item 1), the plastic sleeves (Fig.
7/Item 2) and the star screw (Fig. 7/Item 3).
Using the cable clips supplied (Fig. 8), attach
n
the power cable to the tubes of the push bars so
that it is possible to open and shut the ejector
flap (Fig. 9/Item A).
Important!
n
Please ensure that the ejector flap can be
opened and closed easily!
Assembling the grass basket
(see Figs. 10 and -13)
Push both frame parts into each other (Fig. 10).
n
Pull the grass basket over the metal frame (Fig.
n
11).
Pull the rubber clips over the metal frame (Fig.
n
12).
To hang the grass basket on the scarifier you
n
must lift the ejector flap (Fig. 13/Item 1) with
one hand and with the other hand take hold of
the grass bag by the handle and hook it onto the
scarifier from above (Fig. 13).