Maintenance And Cleaning; Transport; Storage - ATIKA BH 800 N Notice Originale

Maintenance and cleaning

Before each maintenance and cleaning
work:
 switch off device
 wait until the hoeing tools is stationary
 pull out main plug
Maintenance and repair work other than those described in this
chapter is only allowed to be carried out by service staff.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Only use genuine spare parts. Other than genuine parts may
result in unpredictable damages and injury.
Maintenance
The tool will not come to a standstill immediately after cut-off.
Before starting any service work wait until all parts are
stationary.
Pull out mains plug.
To guarantee a long and reliable usage of the product carry out
the following maintainance works regularly.
Check the device for obvious defects such as
 loose fastening elements
 worn or damaged components
 correctly assembled and faultless covers and protective
devices.
Necessary repair works or maintainance have to be carried
out before using the machine.
R e p l a c i n g t h e h o e i n g t o o
R e p l a c i n g t h e h o e i n g t o o
Risk of injury! Wear protective gloves when
working on the hoeing tools.
Worn blades reduce the performance of the device and put
excessive strain on the motor. Therefore check the condition of
the blades before each use.
Have the hoeing tools sharpened by your service workshop or
replace them by new ones if required.
Remove the hexagon screws M 8 x 40 and the hexagon
nuts M 8. Pull then the hoeing tools (13, 14) from the axle.
Pay attention to the correct position of the hoeing tools.
(The tool blades must show towards the working direction.)
Lubricate the gearbox

Lubricate the gear after the first 20 operating hours, then
every 40-50 operating hours.
Put the device on its side and remove the hoeing tool

(14).
 Clean the gear housing from dirt and foreign objects.
 Remove the drain plug (15).
Put the grease gun onto the grease filling plug (17).

 Press some grease in.
l s
l s

Do not fully fill the gearbox. Grease expands due to heat
generated during operation. There is the risk of damages
to seals and grease leakage when the gearbox is fully
filled with grease.
Use SHELL Albida Grease EP 2, for example, or an
equivalent grease brand.
Check the sealing ring (16) for damages and replace it

if required.
 Re-install the drain plug (15) and the hoeing tool (14).
Cleaning
Clean the device carefully after each use to ensure

faultless function to be maintained.
Risk of injury! Wear protective gloves when
working on the hoeing tools.
 Remove the dirt with a cloth or brush.
 Clean the device immediately after finishing the work.
 Clean the bottom of the device and the sets of tines.
 Clean the housing, especially the vent slots, from dirt stuck
to it.
 Do not clean the machine with running water or high-
pressure cleaners.
 Do not use solvents for the synthetic parts (petrol, alcohol,
etc.) as these can damage the synthetic parts.

Transport

For each Transport
 switch off device
 wait until the cutting device does not longer
move
 pull out mains plug
The sets of tines can be damaged during transport, e.g.
on hard ground, even when the motor is switched off.
Therefore carry the device.
Pull out main plug.
 Store unused equipment in a dry, locked place out of the
reach of children.
 In case of extended storage (e.g. during winter) ensure that
the device is protected against frost and corrosion.
 Before extended storage, please observe the following to
increase the service life of the device and to ensure smooth
operation:
 thoroughly clean the device
 Treat metal parts after each use against corrosion using
an environmentally friendly biologically degradable spray
oil.

To store the device space-saving it is possible to fold
down the upper handle hoop (1). For this, loosen the
thumb nut (M6) until you can fold down the handle hoop
(1).

Storage

19