Description Of Device / Spare Parts; Assembly; Start-Up - ATIKA BH 800 N Notice Originale


Protect yourself against electric shocks. Avoid touching
earthed parts with your body (e.g. pipes, heating apparatus,
cookers, fridges etc.).

This device generates an electromagnetic field during
operation. Such a field may affect active or passive medical
implants under certain circumstances. To reduce the risk of
serious injuries we recommend persons who carry medical
implants to consult their doctor and the manufacturer of the
medical implant before operating this device.
 Regularly check the extension cables and replace them if
they are damaged.

Do never connect a damaged cable to the mains. Do not
touch a damaged cable before it is disconnected from the
mains. A damaged cable may cause contact with live parts.
 Do not use any defective connection cables.
 When working outdoors, only use extension cables especially
approved and appropriately labelled for outdoor use.
 Do not set up any provisional electrical connections.
 Never bypass protective devices or deactivate them.
 Only hook up the machine by means of a fault-current circuit
breaker (30 mA).
The electrical connection or repairs to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.

Description of device / spare parts


Please refer to the attached assembly and
operating instruction sheet.
Pos. Denomination
1 Upper handle hoop
2 Switch handle
3 Safety knob
4 Switch-plug combination
5 Cable strain relief
6 Cable clip
7 Lower handle hoop
8 Body cover
9 Screw bag
10 Safety label
11 Handle hoop holder
12 Protective cover
13 Hoeing tool - right
14 Hoeing tool - left
Safety switch
Handle hoop
Mains connection
Compare the voltage given on the machine model plate e.g.
230 V with the mains voltage and connect the machine to the
relevant and properly earthed plug.
Connect the machine via a circuit breaker switch (residual-
current-operated circuit switch) 30 mA.
 Design of the connection cable according to IEC 60245 (H
Mains fuse
Order-no. 10 A inert
381856
Mounting of the extension cable
381855
381858
381859
381857

381853
motion.
381854
381861
Switching on / off
381859 Do not use any device where the switch can not be
switched on and off. Damaged switches must be repaired
381860
or replaced immediately by the customer service.
The device is equipped with a safety circuitry preventing
inadvertent switching on.

Assembly

Open the holder for the switch-plug combination (4). Slide
the switch-plug combination (4) over the holes on the
upper handle hoop (1) and secure it using the provided
screws (2x ST3.9x19).
Secure the lower handle hoop (7) on the hoop holders (11)
on the motor housing. Use the supplied fasteners (2x
screw M5x25, 2x lock nut M5).
Fasten the upper handle hoop (1). Use the supplied
fasteners (2x screw M6x45, 2x flying nut M6). Fix the cable
on the handle hoop using the cable clips (6). Make sure
that the cable has enough free motion.
Attach the cable strain relief (5) on the lower handle hoop
(7).

Start-up

07 RN-F) with a core cross-profile section of at least
- 1.5 mm² for cable lengths up to 25 m
- 2.5 mm for cable lengths over 25 m
2
Plug the female connector of the extension cable on the
male connector of the switch-connector combination (4).
Thread the extension cable through the strain relief (5) as
a loop and hang it up.
Make sure that the extension cable has enough free
Only start the machine when it is placed on a flat ground
area without obstacles.
17